Search Results (909)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
I have a vnx5400 that I haven't used for a long time and I don't remember the login credentials. I am trying to do a password reset with the physical button on the SP (initially in the SPA). I follow the procedure that should work but there is no way.I keep the button pressed for 2-3 seconds, but I
Question
•
VNX
Community Accepted Solution
Hi guys, sorry, my English is not very good. I have both SPS failures on VNX7500, I have both new batteries for repayment and will replace two SPS, I'd like to know if I can replace both SPS online, I replace SPS A end wait for the charger then after charge, I replace SPS B, or if I need shut
Question
•
VNX
Community Accepted Solution
Hi all, I have some VPLEX, VNX systems and KTN-STL3 shelves we want to reuse sanitizing firstly drives. We sanitize common drives with Killdisk software under NIST800-88 regulation but I have seen we have to take care with EMC drives wich firmware could be cleared on this process and have to be ref
Question
•
VNX
Community Accepted Solution
Hi guys, read a lot of topics on how to change ip address on VNX, but still have some questions I would like to clarify.So I have a VNX 5300 which is the only array in a domain. When I try to remove it from the domain the warning says "removing the master will result in deletion of entire domain, in
Question
•
VNX
Community Accepted Solution
I have updated a vnxe3200 from version 3.1.8.9809862 to version 3.1.10.9946299.At the end of the process the update fails with the error: UPGRADE_TASK_esrs3_migrateNow I can't do any more operations on the machineHow can I proceed?Can I go back?The machine in question is out of support and used for
Question
•
VNX
Community Accepted Solution
Hello: Recently we have two fail disk at our VNX 5500. One of them it shows a 'Hot spare disk replacing' state correctly but the other it doesnt appear with their hot spare disk. This failed disk show 'Removed' state.Can we replace this failed disk apparently without hot spare with minimal impact?T
Question
•
VNX
Community Accepted Solution
Hello, I have a VDM built on a VNX 5800 data mover running on File OE 8.1.21-266. Both the VDM and server_2 are on same domain but is it possible to setup different set of DNS servers on VDM because we wanted to run a test? I tried running server_dns and got the message "Error 4035: : server_dns :
Question
•
VNX
Community Accepted Solution
I am trying to run UEMCLI commands to update my VNXe3200 but when I type in the command (i.e., "uemcli -d xxx.xxx.xxx.xxx -u Local/Admin -p AdminPassword /sys/soft/ver show") I get message that just says: -bash: xxxxxxxxx: event not found where the xxxxxxxxx value is the last 12 character
Question
•
VNX
Community Accepted Solution
Dears, help me please find a way to get an answer. We have a problem with one of SAS disks ST600MM0 CLAR600, Part Number DG118033069, Serial Number S0M6xxxx, Firmware LS1F. Could you please help us to find an appropriate replacement for it? Is it possible to change the
Question
•
VNX
Community Accepted Solution
Hi, not sure if anyone can help. I keep getting the below error on my Uni-sphere and not sure what the cause is. I tried looking up information online but didn't find anything. As far as I know it might be doing battery test?? I think so as the faults are always around the same time frame from week
Question
•
VNX
Community Accepted Solution
When I set on private IP 192.168.101.88/255.255.255.0/192.168.101.254 as the Unisphere IP, I got one Unexpected Error, The Error Code is 0x3400003. The OS version is 3.1.15.10216415. Thanks in advanced !
Question
•
VNX
Community Accepted Solution
Yesterday, I want to modify the NTP configuration to set NTP Server on my VNXe3200. But I lost the connect during the operation. After I re-login with Unisphere, I had finished the Disk Firmware upgrading, although the procedure is very slow. And when I want upgrade the Software Version from 3.1.8 t
Question
•
VNX
Community Accepted Solution
Good day , I just purchased a used VNX5300 with the os on the 4 first disk. I did connect to SP-A by Serial port with Putty everything look like it's starting but at one point it's stoping to show the line and here's the information I'm getting from the putty screen on start-up.
Question
•
VNX
Community Accepted Solution
Hello, Can anyone confirm that if we reboot one Storage Processor in EMC VNX5300, the second SP will continue to handle all I/O without any disruption? Thank you in advance for your valuable support. Best Regards,
Question
•
VNX
Community Accepted Solution
Hello, Can anyone confirm that Power Supply boxes A & B on EMC VNX5300 DPE are fully redundant so that we can disconnect power cord from either side A or side B without any disruption or issues? Thank you in advance for your support.
Question
•
VNX
Community Accepted Solution
Good day, In the last few days I found I can't log into my two VNXs I get the unisphere windows but its white without the text boxes for user and password, and even if I try to insert them blindly it doesn't work I tried it vie IE and via VNX launcher, on several computers including Windows 7 com
Question
•
VNX
Community Accepted Solution
Hi, VNXe3200: Able to SSH using service account, but Unisphere unable to authenticate with same credentials used for SSH. Not able to login Unisphere service manager as well with service aacount. Kindly advise. Thanks!
Question
•
VNX
Community Accepted Solution
Hello, Is it possible to migrate LUNs(Datastores) on a VNXe from FC to iSCSI. The VNXe is 98% full and cannot create new LUNs to do the migration. The question is; can I present the same LUN on FC to a host and iSCSI to another host? Or can I reattach a LUN that was presented to the host on the FC
Question
•
VNX
Community Accepted Solution
Hi, Hi does any one know where i can find a download for the Storage Replication Adapter? I can't find it anywhere on Dell/EMC support site.. Vmware compatibility matrix shows me the supported version: SRA Name: EMC VNX SRA with MirrorView Enabler for VNXSRA Version: 5.0.2.84/5.0.39.164
Question
•
VNX
Community Accepted Solution
Hi.Can someone explain to me the underlying process of RAID rebuild logging in VNX or Unity. How does it help rebuild the RAID? The write data is stored in bitmap and when new disk is installed to degraded RAID - it's being rebuild with parity but new parity isn't calculated thanks to the rebuild lo
Question
•
VNX