Search Results (909)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Hi Everyone, I am working with a old EMC VNX300, and i need safely shutdown, and i need know how can i upgrade to a last version of VNX5300.
Question
•
VNX
Community Accepted Solution
I had an apparent failure of a 600 GB SAS disk, P/N 118032757-A02 (Seagate Savvio 10K). My vendor shipped me a 600 GB 10K SAS disk replacement, but it's a Hitachi, P/N 118032767-A04. When I plug the new disk into the same slot as the old disk, the light blinks blue momentarily, then the orange
Question
•
VNX
Community Accepted Solution
Hi, I've got a VNX5100 with two SPs and two SPSs and one of the SPSs has failed. The array is continuing to operate as normal and the write cache is enabled. Can anyone confirm if the SPS replacement is non-disruptive and if there is a documented procedure for doing the replacement? I've
Question
•
VNX
Community Accepted Solution
Hi, I have a shared folder and a windows domain group which only has read permissions but, I would like that this group couldn't copy the files contained in the folder, only read the files. Is there any way to achieve this? Thanks in advance. Regards.
Question
•
VNX
Community Accepted Solution
Hey there, sadly the power calculator was no use since it only showed me the power consumption of the system in total. Could someone tell me the power usage of a single DAE stacked with 15x 2TB / 7200k Disks in kWh ? The System is a VNX5700 used as Block. All of the disks only get used every 5
Question
•
VNX
Community Accepted Solution
Hello. We have a few IP addresses that have FTP connection open on our VNX. We wish to close it down but I'm unable to find this configuration on the Unisphere. I'm not sure but these IP addresses seem to be related with Data Mover server_2, and / or NAS. But the FTP Network Service for the no
Question
•
VNX
Community Accepted Solution
We are preparing to migrate our primary NAS file system from a VNX7500 to a newer Isilon cluster. VNX file version is 7.1.76-4 and the array is no longer under EMC support. Current NAS interface connections are just the 1Gb copper Ethernet ports. The datacenter deployed 10Gb relatively recently.
Question
•
VNX
Community Accepted Solution
Hi Everyone, I have VNX5200 with the following error messages: Bus 0 Enclosure 0 Power A Not Supported Bus 0 Enclosure 0 Power B Not Supported The problem occur after a have upgraded the Flare OE to 05.33.009.5.115 from 05.33.000.5.079 We are not sure what does it mean? whether Pow
Question
•
VNX
Community Accepted Solution
Hello Our network team is changing our DNS servers. Most of what we have is IP based, but the host name entries for the SP are in our DNS servers as well. How do I update the DNS entries for block only VNX 5700 arrays? Thanks in advance, Admingirl
Question
•
VNX
Community Accepted Solution
Title pretty much covers it. I'm being asked to determine if there are any actions upcoming/required in regard to mitigating these two vulnerabilities on any of my storage units. That includes VNX and VNX2 arrays. If the answer was 'yes' to either, then I guess the follow-up would be to as
Question
•
VNX
Community Accepted Solution
Good Afternoon, I'm after some advice on what I'm probably doing wrong with regards to getting LUN replication and failover not working as expected using Windows 2008 R2. I have two VNXe3200's that are configured for LUN replication. VNXe2 is the source and VNXe1 is the destination. The replic
Question
•
VNX
Community Accepted Solution
Hello, Currently we are running out of spares, and we are in the process of decommissioning one of the pools. Once we delete the pool, the pool disks would be unbound. Do we have to do anything else to the unbound disks so that they can act as hot spares?
Question
•
VNX
Community Accepted Solution
Hi guys, We got an EMC VNX 5200 that should be monitored by PRTG, we need to MIB files that import it to PRTG, if you have better solution, please give me. Do you have any experience? we want to monitro LUN, disk status etc. Thank you, MSH
Question
•
VNX
Community Accepted Solution
Good day. VNX 5400; 05.33.008.5.119, Windows 2012 R2 with qlogic hba. I got some problem with Windows host: sometimes it is not displayed in the host list in the Unisphere. However there are no real problem with storage access, this Winddows host works fine as veeam backup direct SAN access proxy
Question
•
VNX
Community Accepted Solution
We recently had an issue where the certificates on our VNX SANs expired and we were not able to access the SANs. I regenerated the certs by logging into the Setup page of each SAN and regenerating the certs from there and it all works good now. However my manager insists that I need to generate a
Question
•
VNX
Community Accepted Solution
Hi All, Where can I get solvedesktop, if it still exists. Can anyone share a link? Appreciate your input.
Question
•
VNX
Community Accepted Solution
Hi Community, I am seeing a high value of 682% for the Read Cache Hit Ratio on our VNX SPA. SPB is only 66%. I am new to VNX, and so I am not sure if this is an acceptable value, or something I should be be concerned about. Any input would be appreciated. Thanks,
Question
•
VNX
Community Accepted Solution
I want to use Unisphere Central but not the curent vApp, i older times there was a program you could install on a windows server is that not awaible any more ?
Question
•
VNX
Community Accepted Solution
I was just asked to retain some specific snapshots/checkpoints on our VNX hosted NAS file system, that will hit their expiration date in a couple of days. I suspect this is a command line process, which I am not very familiar with. I have been reviewing EMC docs and online resources, but not making
Question
•
VNX
Community Accepted Solution
Hi Friends as you know two days ago EMC released OE 05.33.009.5.217 for Vnx2.I tried a lot to find its Release note document but I couldn't.Please let me know where I can find it? thanks in advanced
Question
•
VNX