Search Results (2.9K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
I have a DELL T630 8X3.5 server, and recently I acquired a 12 bay backplane (X4V7W/ 0X4V7W) from a T620 server. I plan to install this backplane into my T630 server, I'm not sure if it will work properly? I checked the dimensions, and it seems compatible. Moreover, the signal cables that come with t
Question
•
PowerEdge Hardware General
Community Accepted Solution
Dear experts, I powered down my DELL PowerEdge R840, moved it into another rack and started it up. Unfortunately the server now hangs on the BIOS screen. I press F2 on boot, but cannot get into the BIOS setup. I've tried restarting. At start a light blinks orange. But after some time the light
Question
•
PowerEdge Hardware General
Community Accepted Solution
Base on windows "System Information" under Components>Storage>Problem Devices- Device not Available PNP device ID ACPI\INTL0000\2&DABA3FF&0 driver are not installed But when I validate through Device manager there are no issues on the drivers. Next step to troubleshoot ? or I can d
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello, I recently bought a DELL PowerEdge T140 server, which didn't come with RAM. Consequently, I had to buy RAM separately. The RAM I chose is the KTD-PE426D8/16G, which is a DDR4 2666MT/s ECC Registered DIMM, and should be compatible with my server as per the manual. Despite this, the server won'
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello everyone, I am seeing Health Information on the IDRac interface of the PowerEdge R750XS rack server I recently built. The server is working fine, but I don't know what this error means. [DELETED because of sensitive Informations]
Question
•
PowerEdge Hardware General
Community Accepted Solution
PowerEdge R320s can take a special module for the iDRAC. It is my understanding that without that iDRAC module physically installed, the machine is only running basic management.Is the basic management a chip on the motherboard that can fail, and assuming that it can and it has, if you were to insta
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi all, I have a Dell R730 with 2 x Xeon E5-2673v4 (20 core), 256 GB RAM, 16 x 2.5" Crucial 2TB SSD configured as a RAID-10 with a H730 Perc controller. On this device are 20 VMs, each configured with 8GB of RAM and 4 vCPU. A couple of the users logging in via RDP are saying that the response time
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi all, Does someone know the part number of this piece? Poweredge R340 right ear Thanks in advance,
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello, how can I wipe the hard drive for a M610. I can go back to defaults with the IRDAC and Bios, but I cannot seem to find a way to wipe the hard drive on the unit. I do not see a Retire or repurpose option in the Lifecycle setup
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi I want to upgrade my server PowerEdge R730 second processor What equipment needed? Please advise
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hello, hope everyone is doing well. Question - If I want to install 2 GPUs in a PowerEdge R940XA server, then would I just need the 16x risers and respective cables? Is there a part number for a GPU Enablement Kit? Thank you
Question
•
PowerEdge Hardware General
Community Accepted Solution
I am unable to find any compatibility list for the PowerEdge R760sx, can someone tell me if it is compatible with the Intel x520 line? If not, what are the suggested cards for this system and CentOS 7? Thanks!
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi All,I have an old T320 which is having the below Issues, Just trying to confirm whether it might be a board issue -No Display on Embedded VGA or Graphics card -No Post (Even with Minimum Requirements for Post) -No Beeping when ram removed -CPU Internal Error - Constantly Power cycles on and off
Question
•
PowerEdge Hardware General
Community Accepted Solution
I have a Power Edge R440 In Open manage under Storage/perc H730P adapter (Embedded)/Connector 0 (RAID)/Enclosure (Backplane)/Physical Disks. I see 5 drives, 2446.62GB i believe to be a mirrored C drive. and 3 893.75 GB drives i expect to be the RAID 5 for D: They are all showing good, but i need to
Question
•
PowerEdge Hardware General
Community Accepted Solution
Hi, My Dell T640 does not turn on, it has 2 power supplies connected, but when I press the power button, it does not start and the LEDs on the motherboard show the following status: DS0 - OFF DS1 - ON DS2 - OFF DS3 - OFF DS4 - OFF DS5 - BLINK DS6 - BLINK Any idea about it.? Thank's a lot.
Question
•
PowerEdge Hardware General
Community Accepted Solution
The powersupply is mentioned with 100-240V 50/60Hz for AC input OR 240V for DC input. This means we can connect 110V AC or 230V AC. However for DC is it only 240V DC, can't we use 120V DC ?? Why the range of DC is not mentioned as like in AC.
Question
•
PowerEdge Hardware General
Community Accepted Solution
Recently added a second CPU to this server. I went with the Xeon E5-2640 v4, but after installing the heatsink and powering it back up, I get hung up on this screen. Any ideas on what is causing this?
Question
•
PowerEdge Hardware General
Community Accepted Solution
We have a T310 PowerEdge Server, with this PCIe slots free: 2 x8 1 x4 2 x1 We need to install an PCIe board with 2 SSD slots, to make an RAID -1 system of SSD disks. But all of this card require Bifurcation support on PCIe slots. Any of the PCIe slots support bifurcation? Thanks Wladimir Estrag
Question
•
PowerEdge Hardware General
Community Accepted Solution
I'm seeing this message in the Hardware Log on my server. I saw in another post that it might be a driver issue. Any thoughts?
Question
•
PowerEdge Hardware General
Community Accepted Solution
After reading https://arstechnica.com/security/2024/04/supply-chain-snafu-causes-intel-and-others-to-ship-hackable-hardware-for-5-years/ and the associated articles, I am curious to know if my T340 has an exposure. Am I worried about it? No, not really however if the main board does have an exposur
Question
•
PowerEdge Hardware General