AUTOMATISCH INSTALLIERTDiese Datei wurde automatisch im Rahmen einer vor Kurzem erfolgten Aktualisierung installiert. Wenn Probleme auftreten, können Sie die Datei manuell herunterladen und erneut installieren.
Der Inhalt dieser Seite wurde möglicherweise automatisch übersetzt. Füllen Sie das Formular unten auf der Seite aus, um Feedback zu geben.
Diese Datei wurde automatisch im Rahmen einer vor Kurzem erfolgten Aktualisierung installiert. Wenn Probleme auftreten, können Sie die Datei manuell herunterladen und erneut installieren.
PERC 4/Di Device Driver for Red Hat Linux 7.2.
Empfohlen
Den besten Download für Ihr System suchen
Bitte geben Sie Ihre Produktdetails ein, um die neuesten Treiberinformationen für Ihr System anzuzeigen.
Support suchen
Dell Service-Tag-Nummer oder Modell eingeben
Sie möchten Ihr Produkt suchen? Geben Sie eine Produktkennung ein.Anleitung
Keine Ergebnisse gefunden. Wir konnten für Ihre Suchanfrage keine Ergebnisse finden. Bitte ändern Sie Ihre Suche und versuchen Sie es erneut.
Dieser Treiber ist nicht kompatibel.
Dieser Treiber ist für das ausgewählte Produkt nicht verfügbar. Wählen Sie ein anderes Produkt aus, um Ihre Produktdetails für diesen Treiber erneut einzugeben, oder besuchen Sie die Seite Produktsupport, um alle Treiber für ein anderes Produkt anzuzeigen.
Melden Sie sich bei Windows als AdministratorIn an, um den automatischen Scan zu nutzen. Wenn Sie bereits als AdministratorIn angemeldet sind und diese Meldung angezeigt wird, führen Sie einen Neustart durch.Ihr System wird von Ihrem IT-Administrator verwaltet und die Funktionen sind möglicherweise eingeschränkt.
Weitere Updates finden. Nutzen Sie SupportAssist, um alle aktuellen Treiberupdates für Ihr Gerät zu finden.
Dell Technologies empfiehlt, dieses Update zu überprüfen, um festzustellen, ob es für Ihr System gilt. Das Update enthält Änderungen, die sich nur auf bestimmte Konfigurationen auswirken, oder bietet neue Funktionen, die für Ihre Umgebung gelten können aber nicht müssen.
Dateiformat:Extrahiert Dateien direkt auf die lokale Festplatte
Dateiname:perc4di-118c-72c.tar.gz
Dateigröße:538.62 KB
Dies ist eine große Datei. Abhängig von Ihrer Verbindungsgeschwindigkeit kann das Herunterladen einige Zeit in Anspruch nehmen.
Beschreibung des Dateiformats:
Dieses Dateiformat umfasst ein Dateiarchiv, das in einem Verzeichnis auf der Festplatte dekomprimiert werden kann. Die Installation kann anschließend von diesem Verzeichnis aus durchgeführt werden.
Instructions for downloading and creating driver diskette: ----------------------------------------------------------
You will need a formatted 3 1/2 inch floppy diskette for the following procedure.
Download the file PERC4di-118c-72c.tar.gz to a temporary directory on your working system.
Extract the file to the floppy disk as follows:
1. On a Linux system:
Type the following commands under a Linux command shell: mount /dev/fd0 /mnt/floppy tar xvzf -C /mnt/floppy (Eg: /temp/PERC4di-118c-72c.tar.gz) umount /mnt/floppy
2. On a Microsoft Windows system:
You can use Winzip to extract tar.gz archives. However, note the following settings under Winzip to ensure correct extraction of the files.
Start Winzip -> Go to Options -> Configuration
Under the Miscellaneous tab make sure "TAR file smart CR/LF conversion" is unchecked.
Upon opening the tar.gz archive with Winzip, you get the following prompt:
'Archive contains one file. Should Winzip decompress it to a temporary folder and open it?'
Press 'yes' and extract the files normally under Winzip to the floppy drive.
Install Red Hat Linux 7.2 driver for PERC 4/Di as a boot controller -------------------------------------------------------
There are two ways of installing Red Hat 7.2 driver onto the PERC 4/Di as a boot controller. One is using a driver disk during OS installation and the second is using a driver (megaraid) RPM to update driver after OS is installed. The steps for both of these methods are provided below. All the files needed for both methods are included in the driver diskette created above.
For more detailed installation instructions of Red Hat 7.2, please refer to the OS installation guide at http://www.dell.com/linux.
I. Installing driver during OS installation: --------------------------------------------
1. Boot normally from the Redhat installation CD-Rom.
2. Type 'linux dd' on the boot prompt.
3. When the install prompts for a driver disk, insert the driver diskette created above and press 'Enter'.
4. Installation progresses normally. Continue until the 'Create Bootdisk' screen. Press CTRL-ALT-F2 to get to a shell window and type the following commands:
chroot /mnt/sysimage cd /boot /sbin/mkinitrd -f initrd-2.4.7-10.img 2.4.7-10 lilo ( only if lilo was used as bootloader. If grub used - skip this step ) exit
Press CTRL-ALT-F7 to get back to the install screen.
5. Complete the installation as directed by the install.
II. Update driver using RPMs after OS is installed --------------------------------------------------
Type the following commands under a Linux command shell:
mount /dev/fd0 /mnt/floppy cd /mnt/floppy ./megarpmwrapper.sh
Than follow the on-screen instructions to install the RPM driver.
For more detailed information about the script megarpmwrapper.sh, please refer to the release_notes.txt included in the release.