Dell OpenManage Deployment Toolkit Version 4.3 Command Line Interface Reference Guide

PDF

Failure Messages

The SYSCFG utility failure messages provide error codes to help diagnose why some commands do not succeed. The following table lists SYSCFG error codes and messages.

Table 1. SYSCFG Error Codes and Messages
Error Code	Message
`0`	`Success`
`1`	`Attempt to read write-only parameter.`
`2`	`Password cannot exceed 16 characters.`
`3`	`A BMC was either not detected or is not supported.`
`4`	`This username is already in use. Enter a unique username.`
`5`	`Access mode not supported.`
`6`	`Cannot return number of requested data bytes.`
`7`	`User ID 1 cannot be assigned a username.`
`8`	`Cannot execute duplicated request.`
`9`	`There was an error clearing the SEL.`
`10`	`Clear SEL cannot be accompanied with any other option.`
`11`	`racreset cannot be accompanied with any other option.`
`12`	`Cannot execute command. Command, or request parameter(s), not supported in present state.`
`13`	`Command not supported on given channel.`
`14`	`The community string may only contain printable ASCII characters.`
`15`	`Destination unavailable. Cannot deliver request to selected destination.`
`16`	`Cannot execute command. Insufficient privilege level.`
`17`	`Command illegal for specified sensor or record type.`
`18`	`Invalid commstring value.`
`19`	`Hardware subsystem error. Invalid data field in Request.`
`20`	`Invalid destination IP address.`
`21`	`The GUID is invalid.`
`22`	`Invalid gateway.`
`23`	`Invalid hostname.`
`24`	`Invalid IP address.`
`25`	`Invalid DNS IP address.`
`26`	`Invalid sub net mask.`
`27`	`Invalid value for PEF. PEF value should be between 1 and 16.`
`28`	`Reservation Canceled or Invalid Reservation ID.`
`29`	`Invalid Time to live value.`
`30`	`Invalid VLANID value.`
`31`	`Invalid Command. Used to indicate an unrecognized or unsupported command.`
`32`	`Command invalid for given LUN.`
`33`	`Load defaults cannot be accompanied with any other option.`
`34`	`There was an error loading the defaults.`
`35`	`Node Busy. Command could not be processed because command processing resources are temporarily unavailable.`
`36`	`Out of space. Command could not be completed because of a lack of storage space required to execute the given command operation.`
`37`	`This parameter is not supported.`
`38`	`Parameter out of range. One or more parameters in the data field of the Request are out of range.`
`39`	`The password may only contain printable ASCII characters.`
`40`	`Password test failed.`
`41`	`Requested data length invalid.`
`42`	`Requested data field length limit exceeded.`
`43`	`Requested Sensor, data, or record not present.`
`44`	`Request data truncated.`
`45`	`Command response could not be provided.`
`46`	`Command response could not be provided. BMC initialization or initialization agent in progress.`
`47`	`Command response could not be provided. Device in firmware update mode.`
`48`	`Command response could not be provided. SDR Repository in update mode.`
`49`	`Cannot execute command, SEL erase in progress.`
`50`	`Attempt to set the 'set in progress' value when not in the 'set in complete' state.`
`51`	`The SOL character ’accumulate interval’ is invalid.`
`52`	`The SOL character ’send threshold’ is invalid.`
`53`	`The SOL ’retry interval’ is invalid.`
`54`	`Command completed successfully.`
`55`	`Time-out while processing command. Response unavailable.`
`56`	`Unspecified error.`
`57`	`The password may only contain printable ASCII characters.`
`58`	`Username cannot exceed 16 characters.`
`59`	`Invalid VLANID value. Enter in ’dddd’ format.`
`60`	`Attempt to write read-only parameter.`
`61`	`BMC is busy.`
`62`	`Response data did not return successfully.`
`63`	`BMC time out error.`
`64`	`Option requires an argument.`
`65`	`The asset tag for this system is not available.`
`66`	`The asset tag cannot be more than 10 characters long.`
`67`	`The required BIOS interfaces cannot be found on this system.`
`68`	`The BIOS version information is not available.`
`69`	`There is not enough free system memory to complete the BIOS update.`
`70`	`The BIOS update file version is a different version class (A00, X00) than the current system BIOS. Use the --force option to use this BIOS image.`
`71`	`The BIOS update file version is older than the current system bios. Use the --force option to use this BIOS image.`
`72`	`The BIOS update file version is identical to the current system bios. Use the --force option to use this BIOS image.`
`73`	`The sequence list must be a comma-separated numerical list of valid unique boot device numbers (ex: 2, 1, 3).`
`74`	`The sequence list must be a comma-separated list of valid unique device names (ex: nic.emb.1, hdd.emb.1) or a comma-separated numerical list of valid unique boot device numbers (ex: 2, 1, 3).`
`75`	`There was an error setting the sequence.`
`76`	`The list is not formatted correctly. See the help for more details.`
`77`	`The size of returned buffer is larger than the size of allocated buffer.`
`78`	`There was a problem getting the state byte.`
`79`	`The state byte is not available on this system.`
`80`	`There was a problem setting the state byte.`
`81`	`The state byte must be a value between 0 and 255 decimal.`
`82`	`The CPU information is not available.`
`83`	`The dependent option required for this subcommand is missing in the command line.`
`84`	`Duplicate sub command has been entered.`
`85`	`The script file does contain not a valid DTK environment script signature.`
`86`	`The format of the environment variable is incorrect.`
`87`	`The --envar option can only be used for a single option.`
`88`	`The --envar option can only be used for report operations.`
`89`	`The individual sub commands should be specified for the -s option.`
`90`	`Getting external serial connector settings failed.`
`91`	`Setting external serial connector settings failed.`
`92`	`There was an error opening the file.`
`93`	`File does not have write permission.`
`94`	`The file contains invalid options.`
`95`	`The replication information does not match for this system.`
`96`	`There can only be one section in the input file.`
`97`	`Bad ini file, the section cannot be found.`
`98`	`The format of the bios image file is incorrect.`
`99`	`Report operations and set operations must be separate.`
`100`	`Help is not available for the option.`
`101`	`The -x (--hex) option can only be used with -b or -r.`
`102`	`Input file not found.`
`103`	`Input file cannot be read.`
`104`	`Invalid argument for option.`
`105`	`Function table lookup error.`
`106`	`The machine ID was not found in the file.`
`107`	`The system memory information is not available.`
`108`	`Mode can only be used with the --pci option.`
`109`	`The device name or index must be present in the boot order.`
`110`	`The output file could not be opened. Please make sure the path exists and the media is not write protected.`
`111`	`Could not write to output file, disk may be full.`
`112`	`The current password must be supplied with a new password using --oldsyspwd.`
`113`	`The current password must be supplied with a new password using --oldsetuppwd.`
`114`	`The current password can only be supplied when setting a new password.`
`115`	`Actions are not allowed for this filter. Only alerts are allowed.`
`116`	`There was an error getting the option.`
`117`	`The option is not available or cannot be configured through software.`
`118`	`There was an error setting the option.`
`119`	`The -n (--namefile) option can only be used with - -pci.`
`120`	`The password may only contain alphanumeric characters.`
`121`	`The BIOS passwords have been disabled via jumper.`
`122`	`The password length must be between 1 and 32.`
`123`	`This password is locked and can only be unlocked by the admin user.`
`124`	`There was an error setting the password.`
`125`	`The LCD string length must be between 1 and %s.`
`126`	`The LCD string may only contain alphanumeric characters.`
`127`	`There was an error setting the LCD string.`
`128`	`The second channel can only be set if the RAID controller is set to RAID.`
`129`	`The set operation requires sub commands.`
`130`	`The service tag for this system is not available.`
`131`	`The system ID value is not available.`
`132`	`The system information string is not available.`
`133`	`A system error has occurred.`
`134`	`Usage error.`
`135`	`The uuid information is not present on this system`
`136`	`Version cannot be accompanied with any other option.`
`137`	`The self-identify blinker timer should be set to 0..255 second(s).`
`138`	`Encrypt key is too long.`
`139`	`Encrypt key is invalid, accepted characters are 0 to 9 or A to F.`
`140`	`Parameter has been temporarily disabled due to a dependency on other settings.`
`141`	`The old password supplied is incorrect. The new password will not be set. Please try again.`
`142`	`Cannot stat /etc/omreg.cfg file. Please ensure /etc/omreg.cfg file is present and is valid for your environment. You can copy this file from the DTK iso.`
`143`	`Getting nicselection settings failed.`
`144`	`HAPI Driver Load Error.`
`145`	`Filter action power reduction is only supported for the system power warn/fail filters.`
`146`	`TPM/TCM Clear settings requires setup password.`
`147`	`There is currently no TPM/TCM Clear request pending.`
`148`	`Password is not required for retrieving the ’%s’ options.`
`149`	`Setup password is required for setting the ’%s’ options.`
`150`	`Invalid Password override.`
`151`	`Invalid TPM/TCM set option.`
`152`	`There was an error setting the TPM/TCM option.`
`153`	`There is no setup password installed on this system.`
`154`	`The setup password supplied is incorrect. Please try again.`
`155`	`Profile should be custom for setting cpupowermode, memorypowermode and fanmode.`
`156`	`There was an error setting the Power Option.`
`157`	`The power cap value entered is out of range. Please try again.`
`158`	`The power cap value entered must be between 0 to 100 if unit is percent.`
`159`	`Invalid IPv6 address. The IPv6 address cannot be link-local or multicast.`
`160`	`Invalid IPv6 address. The IPv6 address specified has incorrect address format.`
`161`	`Invalid IPv6 address. The gateway address specified has incorrect address format.`
`162`	`Invalid IPv6 address. The Primary DNS server address specified has incorrect address format.`
`163`	`Invalid IPv6 address. The Secondary DNS server address specified has incorrect address format.`
`164`	`Invalid IPv6 address. The gateway address specified is invalid.`
`165`	`Invalid configuration. Attempting to apply IPv6 configuration on a non supported platform.`
`166`	`Invalid IPv6 configuration. Attempt to set DNS server address manually while DNS address source is set to auto.`
`167`	`Invalid IPv6 configuration. Attempt to set IPv6 address manually while IPv6 address source is set to auto.`
`168`	`Invalid IPv6 configuration. Attempting to apply IPv6 configuration without loading IPv6 stack.`
`169`	`Invalid IPv4 configuration. Attempting to apply IPv4 configuration with IPv4 disabled.`
`170`	`Invalid IPv6 configuration. Ipv6 address cannot be specified without specifying prefix-length.`
`171`	`Invalid IPv6 configuration. dnssrcv6 cannot be set to auto when ipsrcv6 is set to manual.`
`172`	`Error while executing IPMI Set command.`
`173`	`Error while executing IPMI Get command.`
`174`	`Error during Trap Alert.`
`175`	`Unspecified error.`
`176`	`Getting LCD settings failed.`
`177`	`Invalid configuration. Attempting to set cap when capenable is set to disable.`
`178`	`Invalid configuration. Attempting to set cap when hardware does not support setting.`
`179`	`Invalid Configuration Option.`
`180`	`Cannot execute command. Parameter is illegal because command sub-function has been disabled or is unavailable.`
`181`	`Failed to report the removable flash media redundancy status.`
`182`	`Failed to report the Internal SD Module status.`
`183`	`Error locating the Virtual Media Key on the Modular system.`
`184`	`Error in setting the redundancy option for the Internal SD Modules.`
`185`	`Error in retrieving the redundancy option for the Internal SD Modules.`
`186`	`Error in setting the redundancy option on Modular systems for the Internal SD Modules.`
`187`	`Error in retrieving the vFlash option.`
`188`	`Error in setting the vFlash option.`
`189`	`The set operation failed due to dependency.`
`190`	`The set operation failed because attribute is forced to a value.`
`191`	`Cannot disable this OrderedList’s entries.`
`192`	`The set operation failed because system is busy now . Try again later.`
`193`	`New value for the token not valid.`
`194`	`Token not found.`
`195`	`The set operation failed because System Services and/or CSIOR disabled.`
`196`	`The set operation failed due to pending System Password changes.`
`197`	`The set operation failed due to Password verification failure.`
`198`	`The set operation failed due to previously scheduled job.`
`199`	`The set operation failed because attribute is suppressed.`
`200`	`The set operation failed due to Generic failure.`
`201`	`XML path context creation failed.`
`202`	`Unable to parse XML.`
`203`	`Unable to connect data manager.`
`204`	`'root' privileges required to execute this application.`
`205`	`Invalid alert destination.`
`206`	`The set operation failed due to unspecified error.`
`207`	`Incorrect syntax for help. For more information about a particular command, use the option '-h or --help' followed by the command name. Example: %s -h --asset`