- Notes, Cautions, and Warnings
- About Your System
- Front-Panel Features And Indicators—Tower Mode
- Front-Panel Features And Indicators—Rack Mode
- LCD Panel Features
- Diagnostic Indicators
- Hard-Drive Indicator Patterns
- Back-Panel Features And Indicators
- NIC Indicator Codes
- Power Indicator Codes For Redundant Power Supply
- Power Indicator Codes For Non-Redundant Power Supply
- Other Information You May Need
- Using The System Setup And Boot Manager
- Installing System
Components
- Recommended Tools
- Front Bezel (Optional)
- System Feet—Tower Mode
- Wheel Assembly (Optional)—Tower Mode
- Opening And Closing The System
- Inside The System
- Optical Drives And Tape Drives (Optional)
- Cooling Shroud
- Hard Drives—Hot-Swappable
- Removing a Hot-Swap Hard Drive
- Installing A Hot-Swap Hard Drive
- Removing A 2.5 Inch Hard-Drive Blank
- Installing A 2.5 Inch Hard-Drive Blank
- Removing A 3.5 Inch Hard-Drive Blank
- Installing A 3.5 Inch Hard-Drive Blank
- Removing A 2.5 Inch Hard Drive From A 3.5 Inch Hard-Drive Adapter
- Installing A 2.5 Inch Hard Drive Into A 3.5 Inch Hard-Drive Adapter
- Removing A Hard Drive Or A Hard-Drive Adapter From A Hard-Drive Carrier
- Installing A Hard Drive Or A Hard-Drive Adapter Into A Hard-Drive Carrier
- Hard Drives—Cabled
- Hard-Drive Backplane
- Four-Slot Hard-Drive Blank
- System Memory
- Cooling Fans
- Internal USB Memory Key (Optional)
- PCIe Card Holder (Optional)
- Expansion Cards
- iDRAC Ports Card
- Internal Dual SD Module
- Internal SD Card
- Processors
- Redundant AC Power Supply
- Non-Redundant AC Power Supply
- Power Distribution Board And Power Interposer Board
- System Battery
- Control-Panel
Assembly
- Removing The Control-Panel Assembly
- Installing The Control-Panel Assembly
- Removing The Control Panel
- Installing The Control Panel
- Removing The Control-Panel Board For Systems With LCD Modules
- Installing The Control-Panel Board For Systems With LCD Modules
- Removing The Control-Panel Board For Systems With Diagnostic Indicators
- Installing The Control-Panel Board For Systems With Diagnostic Indicators
- Removing The LCD Module
- Installing The LCD Module
- Removing The VGA Module—Rack Mode
- Installing The VGA Module—Rack Mode
- System Board
- Converting The System From Tower Mode To Rack Mode
- Troubleshooting
Your System
- Troubleshooting System Startup Failure
- Troubleshooting External Connections
- Troubleshooting The Video Subsystem
- Troubleshooting A USB Device
- Troubleshooting A Serial I/O Device
- Troubleshooting A NIC
- Troubleshooting A Wet System
- Troubleshooting A Damaged System
- Troubleshooting The System Battery
- Troubleshooting A Non-Redundant Power Supply
- Troubleshooting Redundant Power Supplies
- Troubleshooting Cooling Problems
- Troubleshooting Cooling Fans
- Troubleshooting System Memory
- Troubleshooting An Internal USB Key
- Troubleshooting An SD Card
- Troubleshooting An Optical Or Tape Drive
- Troubleshooting A Hard Drive
- Troubleshooting Expansion Cards
- Troubleshooting Processor
- Using System Diagnostics
- Jumpers And Connectors
- Technical Specifications
- System Messages
- Getting Help
Dell PowerEdge T320 Systems Owner's Manual
SATA Settings Screen
- Menu Item
- Description
- Embedded SATA
- Allows the embedded SATA to be set to Off, ATA, AHCI, or RAID modes. By default, the Embedded SATA option is set to AHCI.
- Port A
- Auto enables BIOS support for the device attached to SATA port A. Off disables BIOS support for the device. By default, Port A is set to Auto.
- Port B
- Auto enables BIOS support for the device attached to SATA port B. Off disables BIOS support for the device. By default, Port B is set to Auto.
- Port C
- Auto enables BIOS support for the device attached to SATA port C. Off disables BIOS support for the device. By default, Port C is set to Auto.
- Port D
- Auto enables BIOS support for the device attached to SATA port D. Off disables BIOS support for the device. By default, Port D is set to Auto.
- Port E
- Auto enables BIOS support for the device attached to SATA port E. Off disables BIOS support for the device. By default, Port E is set to Auto.
- Port F
- Auto enables BIOS support for the device attached to SATA port F. Off disables BIOS support for the device. By default, Port F is set to Auto.
Proporcione calificaciones (1 a 5 estrellas).
Proporcione calificaciones (1 a 5 estrellas).
Proporcione calificaciones (1 a 5 estrellas).
Seleccione si el artículo fue útil o no.
Los comentarios no pueden contener estos caracteres especiales: <>"(", ")", "\"