Passer au contenu principal
Quitter

Bienvenue dans l’univers Dell

Mon compte
  • Passer des commandes rapidement et facilement
  • Afficher les commandes et suivre l’état de votre expédition
  • Créez et accédez à une liste de vos produits
  • Gérer vos sites, vos produits et vos contacts au niveau des produits Dell EMC à l’aide de la rubrique Gestion des informations de l’entreprise.
Se connecter Créer un compte Connexion au compte Premier Connexion au programme de partenariat
Nous contacter

Vos paniers Dell.com

Dell OpenManage Server Administrator Version 7.4 Command Line Interface Guide

PDF

Omconfig Controller Commands

The following table provides the omconfig command syntax required to execute controller tasks.
  • CAUTION: The omconfig storage controller action=resetconfig controller=id resets the controller configuration. Resetting the controller configuration permanently destroys all data on all virtual disks attached to the controller. System or boot partition residing on these virtual disks is destroyed.
Table 1. Omconfig Controller Commands
Required Command Levels (1, 2, 3) Optional name=value pairs
omconfig storage controller action=rescan controller=id
  action=enablealarm controller=id
  action=disablealarm controller=id
  action=quietalarm controller=id
  action=testalarm controller=id
  action=resetconfig controller=id [force=yes]
 
action=createvdisk controller=id raid=<c | r0 | r1| r1c | r5 | r6 | r10 | r50 | r60> size=<number | b | m | g | max | min> pdisk=<PDISKID> [stripesize=< 2kb | 4kb | 8kb | 16kb | 32kb | 64kb | 128kb | 256kb | 512kb | 1mb >] [cachepolicy=<d | c>] [readpolicy=<ra | nra | ara | rc | nrc>] [writepolicy=<wb | wt | wc | nwc | fwb>] [diskcachepolicy=<disabled | enabled>] [name=<string>] [spanlength=<n>] | [secureflag=yes] [vdpienabled=yes]
  • NOTE: For RAID 10 on SAS controllers with firmware version 6.1 and later, spanlength is an optional parameter (default=2).
  action=setrebuildrate controller=id rate=<0 to 100>
  action=setchangecontrollerproperties controller=<id> [bgirate=<rate>][reconstructrate=<rate>][checkconsistencyrate=<rate>][rebuildrate=<rate>][clearredundantpath=clear][abortcheckconsistencyonerror=<enabled/disabled>][loadbalance=<auto/disabled>][allowrevertibilehotspareandreplacemember=enabled/disabled] [autoreplacememberonpredictivefailure=<enabled/disabled>][persistenthotspare=enabled/disabled]rate=<0 to 100>
  action=discardpreservedcache controller=id force=<enabled/disabled>
 
action=createsecuritykey controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
 
action=changesecuritykey controller=id keyid=<keyid> passphrase=<passphrase string> oldpassphrase=<oldpassphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
  action=deletesecuritykey controller=id
  action=setbgirate controller=id rate=<0 to 100 >
  action=setreconstructrate controller=id rate=<0 to 100>
  action=setcheckconsistencyrate controller=id rate=<0 to 100>
  action=exportlog controller=id
  action=importsecureforeignconfig controller=id passphrase=<passphrase for imported foreign configuration>
  action=importforeignconfig controller=id
  action=importrecoverforeignconfig controller=id
  action=clearforeignconfig controller=id
 
action=setpdiskpwrmanagement controller=id spindownunconfigureddrives=<enabled/disabled> spindownhotspares=<enabled/disabled> spindownconfigureddrives=<enabled/disabled> idlec=<enabled/disabled> spindowntimeinterval=<30 to 1440>(minutes) spinupstarttime=<HH:MM:AM/PM> spinuptimeinterval=<1 to 24>(hours)
  • NOTE: Specify spinupstarttime and spinuptimeinterval only when you set spindownconfigureddrives=enabled.
  action=setpatrolreadmode controller=id mode=<manual | auto | disable>
  action=startpatrolread controller=id
  action=stoppatrolread controller=id
  action=createcachecade controller=id pdisk=<PDISKID> [name=<string>]
 
action=enablelkm controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
 
action=switchtolkm controller=id keyid=<keyid> passphrase=<passphrase string> [escrow=yes] [filepath=<Absolute path to the escrow file>]
  • NOTE: If you set escrow=yes, specify the escrow file path.
  action=rekeylkm controller=id
  action=convertraidtononraid controller=id pdisk=<PDISKID>
  action=convertnonraidtoraid controller=id pdisk=<PDISKID>

Évaluez ce contenu

Précis
Utile
Facile à comprendre
Avez-vous trouvé cet article utile ?
0/3000 characters
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez attribuer une note (1 à 5 étoiles).
  Veuillez indiquer si l’article a été utile ou non.
  Les commentaires ne doivent pas contenir les caractères spéciaux : <>()\