Pular para o conteúdo principal
Sair

Boas-vindas à Dell

Minha conta
  • Faça pedidos de forma rápida e simples
  • Visualize os pedidos e acompanhe o status de envio
  • Crie e acesse uma lista dos seus produtos
  • Gerencie seus sites, produtos e contatos de nível de produto da Dell EMC usando o Company Administration.
Login Crie sua conta Premier login Inscrição no programa de parceria
Fale Conosco

Seus carrinhos no Dell.com

iDRAC 8/7 v2.30.30.30 User’s Guide

PDF

Network settings

To configure the Network Settings:
  • NOTE: For information about the options, see the iDRAC Settings Utility Online Help.
  1. Under Enable NIC, select the Enabled option.
  2. From the NIC Selection drop-down menu, select one of the following ports based on the network requirement:
    • Dedicated — Enables the remote access device to use the dedicated network interface available on the Remote Access Controller (RAC). This interface is not shared with the host operating system and routes the management traffic to a separate physical network, enabling it to be separated from the application traffic.

      This option implies that iDRAC's dedicated network port routes its traffic separately from the server's LOM or NIC ports. About managing network traffic, the Dedicated option allows iDRAC to be assigned an IP address from the same subnet or different subnet in comparison to the IP addresses assigned to the Host LOM or NICs.

      • NOTE: In blade servers, the Dedicated option is displayed as Chassis (Dedicated) .
    • LOM1
    • LOM2
    • LOM3
    • LOM4
    • NOTE: In the case of rack and tower servers, two LOM options (LOM1 and LOM2) or all four LOM options are available depending on the server model. In blade servers with two NDC ports, two LOM options (LOM1 and LOM2) are available and on server with four NDC ports, all four LOM options are available.
    • NOTE: Shared LOM is not supported on the following bNDCs if they are used in a full — height server with two NDCs because they do not support hardware arbitration:
      • Intel 2P X520–k bNDC 10 G
      • Emulex OCM14102–N6–D bNDC 10 Gb
      • Emulex OCm14102-U4-D bNDC 10 Gb
      • Emulex OCm14102-U2-D bNDC 10 Gb
      • QLogic QMD8262–k DP bNDC 10 G
  3. From the Failover Network drop-down menu, select one of the remaining LOMs. If a network fails, the traffic is routed through the failover network.

    For example, to route the iDRAC network traffic through LOM2 when LOM1 is down, select LOM1 for NIC Selection and LOM2 for Failover Network.

    • NOTE: If you have selected Dedicated in NIC Selection drop-down menu, the option is grayed-out.
    • NOTE: Failover is not supported on shared LOM for the following Emulex rNDCs and bNDCs:
      • Emulex OCM14104-UX-D rNDC 10 Gbx
      • Emulex OCM14104-U1-D rNDC 10 Gb
      • Emulex OCM14104-N1-D rNDC 10 Gb
      • Emulex OCM14104B-N1-D rNDC 10 Gb
      • Emulex OCM14102-U2-D bNDC 10 Gb
      • Emulex OCM14102-U4-D bNDC 10 Gb
      • Emulex OCM14102-N6-D bNDC 10 Gb
    • NOTE: On Dell PowerEdge FM120x4 and FX2 servers, Failover Network is not supported for the chassis sled configurations. For more information about the chassis sled configurations, see the Chassis Management Controller (CMC) User’s Guide available at dell.com/idracmanuals.
    • NOTE: On PowerEdge FM120x4 servers, while configuring the Enhanced Network Adapter Isolation, ensure that LOM2 is disabled on the host system and is not selected for iDRAC NIC. For more information about the chassis sled configurations, see the Chassis Management Controller (CMC) User’s Guide available at dell.com/idracmanuals.
  4. Under Auto Negotiation, select On if iDRAC must automatically set the duplex mode and network speed. This option is available only for dedicated mode. If enabled, iDRAC sets the network speed to 10, 100, or 1000 Mbps based on the network speed.
  5. Under Network Speed, select either 10 Mbps or 100 Mbps.
    • NOTE: You cannot manually set the Network Speed to 1000 Mbps. This option is available only if Auto Negotiation option is enabled.
  6. Under Duplex Mode, select Half Duplex or Full Duplex option.
    • NOTE: If you enable Auto Negotiation, this option is grayed-out.

Classifique este conteúdo

Preciso
Úteis
Fácil de entender
Este artigo foi útil?
0/3000 characters
  Forneça as classificações (de 1 a 5 estrelas).
  Forneça as classificações (de 1 a 5 estrelas).
  Forneça as classificações (de 1 a 5 estrelas).
  Selecione se o artigo foi útil ou não.
  Os comentários não podem conter estes caracteres especiais: <>()\