This post is more than 5 years old
2 Intern
•
193 Posts
0
4599
latest Flare for CX4-120
My flare OE is 04.28.000.5.504 - where i can find the latest verison for upgrading my flare? is there any need for upgrade from this OE?
This post is more than 5 years old
2 Intern
•
193 Posts
0
4599
Top
RyanP2
261 Posts
0
July 21st, 2009 08:00
04.28.000.5.706
This is CX4, Flare 28, 000 means all CX4 arrays, 5 means customer released code, and 706 is minor path number (higher than the one you have now).
-Ryan
Bomb_29390e
2 Intern
2 Intern
•
193 Posts
0
July 21st, 2009 07:00
RyanP2
261 Posts
0
July 21st, 2009 07:00
SPs reboot one at a time. No downtime required, but low IO time is suggested.
-Ryan
Bomb_29390e
2 Intern
2 Intern
•
193 Posts
0
July 21st, 2009 07:00
btw - i am using NST to check for any upgrade and hot fixes and the system telling me i am up to date? i remmber using NST for upgrading my flare on a diffrent array i have? can i do it from NST or must download it?
RyanP2
261 Posts
1
July 21st, 2009 07:00
I do suggest to upgrade and yes you can use the NST.
-Ryan
Bomb_29390e
2 Intern
2 Intern
•
193 Posts
0
July 21st, 2009 07:00
and just to verify this will not require a downtime to the system as i will do it SP at at a time?
RyanP2
261 Posts
1
July 21st, 2009 07:00
Home > Support > Software Downloads and Licensing > Downloads C > CLARiiON CX4
I suggest upgrading to the latest release as there is an ETA out against the code you are currently running (SP reboot issue with Analyzer - Primus emc215284)
-Ryan
Bomb_29390e
2 Intern
2 Intern
•
193 Posts
0
July 21st, 2009 08:00
DELL-Phani M
14 Posts
0
August 20th, 2009 00:00
Thanks
Phani
kelleg
4.5K Posts
0
August 20th, 2009 07:00
There is a lot of information available on PowerLink about the upgrade process - check in the following locations:
Home > Support > Technical Documentation and Advisories > Hardware/Platforms Documentation > CLARiiON CX3 UltraScale Series Systems
Home > Support > Technical Documentation and Advisories > Hardware/Platforms Documentation > CLARiiON CX4 UltraScale Series Systems
glen
RRR
2 Intern
2 Intern
•
5.7K Posts
0
September 14th, 2009 03:00
kelleg
4.5K Posts
0
September 14th, 2009 08:00
glen
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
October 8th, 2009 11:00
Can I ask yous a question about upgrading Flare28 to 29?
First, the customer considered to upgrade their CX4s from Release 28 p504 to p706, as ETAs existed discussed before.
However, the customer highly utilizes their environment with VMWare, so now they are intersted in the new features of R29 and plan to upgrade from R28 to 29.
MY QUESTION IS: CAN 'NDU' BE PERFORMED FOR INTER-RELEASE(from 28 to 29) UPGRADE EVEN THE RELEASE NUMBER WILL BE CHANGED??
thanks,
Tono
kelleg
4.5K Posts
0
October 8th, 2009 12:00
For internal EMC questions you should use the EMC internal web sites. This forum is a customer forum and while this question is general in nature, you should always use the internal forums for EMC questions.
glen
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
October 8th, 2009 20:00
Thank you very much for your reply and kindly advice.
Please excuse me of my mistake, I'll be more careful from now on.
Thank you,
Tono