This post is more than 5 years old
15 Posts
0
2876
san copy Initiators
I am doing san copy migrations from cx 300 to cx 400, did zoning part correctly. Due to problem in creating san copy connections , I did deregister and when i want to register again I don't see those Initiators in cx 300 connectivity status. Zoning is Intact. how do i see these Initiators again in Connectivity status of CX 300 ?
Any suggestions please.
Thanks
Regards
Prawinready
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 19:00
take a look at this thread, make sure you specify correct WWN when you define source and target LUNs
https://community.emc.com/message/412323#412323
prawinready
15 Posts
0
February 3rd, 2010 08:00
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 08:00
Do you have SanCopy installed on CX400 ?
This e-mail message (including any attachments) is for the sole use of
the intended recipient(s) and may contain confidential and privileged
information. If the reader of this message is not the intended
recipient, you are hereby notified that any dissemination, distribution
or copying of this message (including any attachments) is strictly
prohibited.
If you have received this message in error, please contact
the sender by reply e-mail message and destroy all copies of the
original message (including attachments).
prawinready
15 Posts
0
February 3rd, 2010 08:00
Yes Sancopy is installed on cx4, created san copy sesssions for sp A luns and valiadated connections .I did deregister sp B Initiators in connectivity status, want to register but they dont showup in Connectivity status now .
The luns I want to migrate are of SP B,(Source and destination.)
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 08:00
Did you try SAN Copy > Update connections
This e-mail message (including any attachments) is for the sole use of
the intended recipient(s) and may contain confidential and privileged
information. If the reader of this message is not the intended
recipient, you are hereby notified that any dissemination, distribution
or copying of this message (including any attachments) is strictly
prohibited.
If you have received this message in error, please contact
the sender by reply e-mail message and destroy all copies of the
original message (including attachments).
prawinready
15 Posts
0
February 3rd, 2010 09:00
kelleg
4.5K Posts
0
February 3rd, 2010 09:00
In Connectivity Status in the lower left corner, check the box called "Show Storage System Initiators"
glen
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 09:00
Try to drop zones between the two arrays and add them back, after that SanCopy > update connections
This e-mail message (including any attachments) is for the sole use of
the intended recipient(s) and may contain confidential and privileged
information. If the reader of this message is not the intended
recipient, you are hereby notified that any dissemination, distribution
or copying of this message (including any attachments) is strictly
prohibited.
If you have received this message in error, please contact
the sender by reply e-mail message and destroy all copies of the
original message (including attachments).
prawinready
15 Posts
0
February 3rd, 2010 10:00
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 11:00
can you try restarting management server, it will not discrupt fiber channel traffic.
http://SP_A/setup
select restart Management server.
prawinready
15 Posts
0
February 3rd, 2010 16:00
I did changed the zone again to different initiators and it worked. validated connections and created sessions sucessfully.
I created Incremental sessions for 2 10 gb luns but when i try to create at 3rd big lun of 1TB the sancopy create session hangs up at finish screen. It never ends , doesnt give error.
soruce cx 300.
destination cx 4.
Thanks
Regards
Prawinready
prawinready
15 Posts
0
February 3rd, 2010 18:00
Yes RLP has enough luns and 30% of the total sancopy storage. Is there anything that cx 300 will not support migration of luns with size more than 1TB ?.
Nope I Never used navicli and Dont have much knowledge on that. Do let me know if you have steps to do sancopy throught navicli.
Thanks
Prawinready
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 3rd, 2010 18:00
prawinready
15 Posts
0
February 4th, 2010 08:00
Sancopy create session worked with navicli.
Thanks for the help.
Thanks
Regards
Prawinready
dynamox
1 Rookie
1 Rookie
•
20.4K Posts
0
February 4th, 2010 10:00