Unsolved

This post is more than 5 years old

2 Posts

16551

April 12th, 2013 06:00

Power connect 2816 crach, try to restore

I had a crash of my powerconnect 2816 and it does not respond anymore I get the following, because there is no startup configuration

------ Performing the Power-On Self Test (POST) ------

UART Channel Loopback Test........................PASS

Testing the System SDRAM..........................PASS

Boot1 Checksum Test...............................PASS

Boot2 Checksum Test...............................PASS

Flash Image Validation Test.......................PASS



BOOT Software Version 1.0.0.12 Built  08-Feb-2009  17:19:21
 Board Type - PowerConnect 2816
 PowerConnect 2816 board based on FireFox 88E6218 ARM946E-S processor
 64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.


MAC Address   :  5c:26:0a:ce:f9:27.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
 100%
Decompressing SW from image-1
 100%

OK
Running from RAM...
Operational Mode old state managed; new state unmanaged
Operational Mode - new mode is unmanaged

*********************************************************************
*** Running  SW  Ver. 1.0.0.38  Date  12-Jan-2010  Time  09:19:40 ***
*********************************************************************

HW version is 00.00.02
Base Mac address is: 5c:26:0a:ce:f9:27
Dram size is  : 64M bytes
Dram first block size is  : 46380K bytes
Dram first PTR is  : 0x12B5000
Flash size is: 8M
01-Jan-2000 00:00:05 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
Slot 1 - PowerConnect 2816

------------------------------------
-- Unit Standalone                --
------------------------------------

Tapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 00:00:16 %INIT-I-InitCompleted: Initialization task is completed


Unknown parameter
May be one from the following list:

debug             help              mcli

>01-Jan-2000 00:00:16 %SNMP-I-CDBITEMSNUM: Number of startup configuration items
 loaded: 0

Operational Mode: Deleting IP addresses
01-Jan-2000 00:00:19 %LINK-W-Down:  g1
01-Jan-2000 00:00:20 %LINK-W-Down:  g2
01-Jan-2000 00:00:20 %LINK-W-Down:  g3
01-Jan-2000 00:00:20 %LINK-W-Down:  g4
01-Jan-2000 00:00:20 %LINK-W-Down:  g5
01-Jan-2000 00:00:20 %LINK-W-Down:  g6
01-Jan-2000 00:00:20 %LINK-W-Down:  g7
01-Jan-2000 00:00:20 %LINK-W-Down:  g8
01-Jan-2000 00:00:20 %LINK-W-Down:  g9
01-Jan-2000 00:00:20 %LINK-W-Down:  g10
01-Jan-2000 00:00:20 %LINK-W-Down:  g11
01-Jan-2000 00:00:20 %LINK-W-Down:  g12
01-Jan-2000 00:00:20 %LINK-W-Down:  g13
01-Jan-2000 00:00:20 %LINK-W-Down:  g14
01-Jan-2000 00:00:20 %LINK-W-Down:  g15
01-Jan-2000 00:00:20 %LINK-W-Down:  g16

>

2 Posts

April 23rd, 2013 00:00

BOOT Software Version 1.0.0.12 Built  08-Feb-2009  17:19:21

Board Type - PowerConnect 2816

PowerConnect 2816 board based on FireFox 88E6218 ARM946E-S processor  

64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.

MAC Address   :  5c:26:0a:ce:f9:27.

Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.

Preparing to decompress...

100%

Decompressing SW from image-1

100%

OK

Running from RAM...

Operational Mode old state managed; new state unmanaged

Operational Mode - new mode is unmanaged

*********************************************************************

*** Running  SW  Ver. 1.0.0.42  Date  17-Feb-2011  Time  13:52:08 ***

*********************************************************************

HW version is 00.00.02

Base Mac address is: 5c:26:0a:ce:f9:27

Dram size is  : 64M bytes

Dram first block size is  : 46380K bytes

Dram first PTR is  : 0x12B5000

Flash size is: 8M

01-Jan-2000 00:00:05 %CDB-I-LOADCONFIG: Loading startup configuration.

Device configuration:

Slot 1 - PowerConnect 2816

------------------------------------

-- Unit Standalone                --

------------------------------------

Tapi Version: v1.3.3.1

Core Version: v1.3.3.1

01-Jan-2000 00:00:16 %INIT-I-InitCompleted: Initialization task is completed

Unknown parameter

May be one from the following list:

debug             help              mcli              

>01-Jan-2000 00:00:16 %SNMP-I-CDBITEMSNUM: Number of startup configuration items loaded: 0

There is no startup config on the switch, as far as I have seen I can load a config in debug mode, but I have no config of a 2816 switch.

PS all software is now up to date.

No Events found!

Top