Unsolved
This post is more than 5 years old
8 Posts
0
3219
dell force s50
Hello everyone I state that I am new to these things. I have a problem with a force of s50 because I can not start it with the lan ports, the status panel shows me the green lights on "OK" and "PWR". I followed the procedures as described on the DELL website with the PUTTY program but without success. Can someone help me? Thank you in advance
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
February 6th, 2018 16:00
Hi,
Have you tried connecting with a console cable? Page 9 http://www.force10networks.com/CSPortal20/KnowledgeBase/DOCUMENTATION/InstallGuidesQuickrefs/S-Series/S50_Quick_Reference2.2.0.pdf
Gianko
8 Posts
0
February 8th, 2018 02:00
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
February 8th, 2018 10:00
Was it working previously? It sounds like it might not be booting at all. When you connected the console cable did you reboot the switch to see if any of the boot process comes up?
Gianko
8 Posts
0
February 8th, 2018 11:00
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
February 8th, 2018 14:00
Can you private message me the service tag?
Gianko
8 Posts
0
February 9th, 2018 01:00
Hi Josh
How can I write to you in private?
THX
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
February 9th, 2018 08:00
If you click the envelope icon next to the login bottom in the top right of the page you can send private messages.
Gianko
8 Posts
0
February 10th, 2018 14:00
DELL-Josh Cr
Moderator
Moderator
•
8.7K Posts
0
February 12th, 2018 09:00
It seems like it may be a hardware issue, but it is out of warranty. You may need to call in and see what support options you have there for out of warranty units.
MK.W
27 Posts
0
February 13th, 2018 17:00
dont use cisco blue console cable , that is incorrect. S50 console cable should be straight-through cable
Gianko
8 Posts
0
February 14th, 2018 01:00
Hi MK.W
ok I will use a direct cable but must be used together with a DB9 adapter
or direct from terminal to switch and with which program can I use it?
Thank you
Gianko
MK.W
27 Posts
0
February 14th, 2018 08:00
please take a look at below picture.
https://www.amazon.com/Cisco-DB9-Female-RJ-45-Adapter/dp/B00CLX4LL8
Gianko
8 Posts
0
February 14th, 2018 08:00
Hi MK.W
I saw the link you sent me, I have this type of adapter and I tried to connect it with a straight lan rj45 cable,
but the switch does not receive any connection screen with PUTTY.
Thank you for your interest
Gianko
MK.W
27 Posts
0
February 15th, 2018 02:00
1. do you have a cisco RS232 adapter ? other brand RS232 adapter have same appearance as cisco. but its Line sequential is different with cisco's.
2. use your current adapter, then make a Reverse sequence cable by yourself. for example: A point copper order is 1,2,3,4,5,6,7,8 ; peer B point coppter order is 8,7,6,5,4,3,2,1. then use this cable attach to your RS232 adapter and insert to switch console port . try it again, if the console terminal still not output. that is all , you can give up this S50 switch.
3.i suggest you use putty as console terminal. and its parameter must like below:
baud:9600 data bits :8 stop bits:1 parity:none flow control:none