Unsolved
This post is more than 5 years old
9 Posts
0
6305
how to enable IPv6 forwarding on switch Dell S4128f
Dear all,
Pls help me zzz I have a incident :
When i enter this command : ipv6 nd prefix default no-advertise
then switch report:
% Error: Interface port-channel100, Attempt to configure router advertisements when ipv6 forwarding is disabled..
and I can't find guide or template to enable ipv6 forwarding.
Thanks and best regards,
Haipx
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
September 14th, 2018 06:00
The command to enable ipv6 forwarding is #ipv6 enable.
Page 325: https://dell.to/2xfZHYJ
Hope this helps.
haipx1412a
9 Posts
0
September 16th, 2018 21:00
I'm sorry for reply too late,
But device Dell 4128f difirent with 4048 and it doesn't has command ipv6 enable
s4128f(conf-if-po-100)# ipv6 ?
access-group Specify access control for packets
address Set the IPV6 address of an interface
nd IPv6 interface Neighbor Discover subcommands
ospf Configure interface specific OSPFv3 properties
policy Configure PBR feature
s4128f(conf-if-po-100)# ipv6
pls help me zz thanks
haipx1412a
9 Posts
0
September 16th, 2018 23:00
This is version of my switch :
s4128f# show version
Dell EMC Networking OS10 Enterprise
Copyright (c) 1999-2017 by Dell Inc. All Rights Reserved.
OS Version: 10.3.1E
Build Version: 10.3.1E(152)
Build Time: 2017-11-03T10:44:40-0700
System Type: S4128F-ON
Architecture: x86_64
Up Time: 2 weeks 01:47:24
Pls help
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
September 17th, 2018 05:00
Does this interface have an IPV6 address?
Example:
OS10(config)# interface ethernet 1/1/1
OS10(conf-if-eth1/1/1)# ipv6 address 2111:dddd:0eee::22/128
OS10(conf-if-eth1/1/1)# ipv6 enable
haipx1412a
9 Posts
0
September 17th, 2018 18:00
The switch 4128F doesn't has command that "ipv6 enable" :(
In mode config interface just have 5 value :
1- IPv6 access-group
2- ipv6 address
3- ipv6 nd
4-ipv6 ospf
5 ipv6 policy
Pls check and feedback for us soon
Thanks
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
September 18th, 2018 12:00
I tested this out on a lab switches and the command is present in our lab.
The only difference I see here, is the OS version. Do you have a window you could use to update the switch?
haipx1412a
9 Posts
0
September 18th, 2018 19:00
Your switch is S4248 but my switch is S4128, what do it have different?
pls help check with S4128 , if new version (OS) can resolve problem , i will upgrade OS.
Many thanks
haipx1412a
9 Posts
0
September 19th, 2018 19:00
Dear Daniel, Pls send to me link download OS 10.4.x.x for switch S4128F , , I was to try search on web-dell but i don't found link-download , thanks
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
September 20th, 2018 05:00
Have you tried a different port-channel? Or an individual interface? To see if there is any difference. I don't have access to a 4128, but the OS is the same between the two model switches.
You will need to login to your force10 account to access the download.
https://bit.ly/2MLugLt
There is a tab specific to OS10, which will list all of the OS10 versions.
haipx1412a
9 Posts
0
September 21st, 2018 01:00
because servive is running on my switch so i can't to try diffent port. we just only one uplink
i haven't account and i can't create new zzz
Anonymous
5 Practitioner
5 Practitioner
•
274.2K Posts
0
September 21st, 2018 06:00
Sorry, I should clarify, I am not implying you move any connections around, rather just check to see if the command is available to other interfaces.