Unsolved
This post is more than 5 years old
9 Posts
0
23350
Cisco Catalyst 3550 to Dell PowerConnect 6248P migration
I am trying to mimic the configuration of my existing Cisco Catalyst 3550 switch to our new Dell PowerConnect 6248P. I am very familiar with the Cisco IOS but am struggling with the interface for the Dell switch. I was wondering if anyone could help me with the corresponding Dell commands in order to replicate the existing Cisco configuration. It is primarily the first 6 ports and the standard access ports and VLANs are straight forward. I have attached the related portion of my Cisco configuration. Please let me know what the configuration should look like for ports 1, 2, 3, 5, & 6. Anything you can give me a heads up on is greatly appreciated. Thank you!
MDF3550#sh run
Building configuration...
Current configuration : 4175 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname MDF3550
!
enable secret 5 XXXXXXXXXX
!
username tsadmin privilege 15 password 7 XXXXXXXXXX
ip subnet-zero
ip routing
!
spanning-tree mode pvst
spanning-tree extend system-id
!
interface FastEthernet0/1
description to 2600 Router
switchport mode access
spanning-tree portfast
!
interface FastEthernet0/2
description to 8000M
switchport trunk encapsulation dot1q
switchport mode trunk
!
interface FastEthernet0/3
description to Cisco 1310
switchport trunk encapsulation dot1q
switchport trunk native vlan 100
switchport mode trunk
!
interface FastEthernet0/4
switchport mode dynamic desirable
!
interface FastEthernet0/5
description MDF-1200-2 on North beam
switchport trunk encapsulation dot1q
switchport trunk native vlan 102
switchport mode trunk
!
interface FastEthernet0/6
description MDF-1200-1 on South Beam
switchport trunk encapsulation dot1q
switchport trunk native vlan 102
switchport mode trunk
bh1633
909 Posts
0
June 10th, 2009 16:00
The differnces are commented out below.
MDF3550#sh run
Building configuration...
Current configuration : 4175 bytes
!
! version 12.1
! no service pad
! service timestamps debug uptime
! service timestamps log uptime
! service password-encryption
!
hostname MDF3550
!
! enable secret 5 XXXXXXXXXX
!
username tsadmin privilege 15 password 7 XXXXXXXXXX
! ip subnet-zero
ip routing
!
! spanning-tree mode pvst
! spanning-tree extend system-id
! NOTE: PowerConnect does not support PVST. It enables RST by default
!
! interface FastEthernet0/1
interface ethernet 1/g1
! description to 2600 Router
description "to 2600 Router"
switchport mode access
spanning-tree portfast
exit
!
! interface FastEthernet0/2
interface ethernet 1/g2
!description to 8000M
description "to 8000M"
! switchport trunk encapsulation dot1q
switchport mode trunk
! NOTE: you have explicitly add vlans to trunks on PowerConnect
switchport trunk allowed vlan add a,b,c,d
exit
!
!interface FastEthernet0/3
interface ethernet 1/g3
! description to Cisco 1310
description "to Cisco 1310"
! switchport trunk encapsulation dot1q
! switchport trunk native vlan 100
! switchport mode trunk
! NOTE: the 6248 does not support native vlan command. You can accomplish the same thing with the follwoing general mode commands.
switchport mode general
swithport general allowed vlan add a,b,c,d tagged
switchport general allowed vlan add 100 untagged
switchport general pvid 100
exit
!
! interface FastEthernet0/4
interface ethernet 1/g4
! switchport mode dynamic desirable
! NOTE: PowerConnect does not support this feature. You will either have to statically define the vlans on this trunk port or use GVRP in your network.
switchport mode trunk
switchport trunk allowed vlan add a,b,c,d
exit
!
! interface FastEthernet0/5
interface ethernet 1/g5
description MDF-1200-2 on North beam
! switchport trunk encapsulation dot1q
! switchport trunk native vlan 102
! switchport mode trunk
! NOTE: the 6248 does not support native vlan command. You can accomplish the same thing with the follwoing general mode commands.
switchport mode general
swithport general allowed vlan add a,b,c,d tagged
switchport general allowed vlan add 100 untagged
switchport general pvid 102
exit
!
interface FastEthernet0/6
interface ethernet 1/g6
! description MDF-1200-1 on South Beam
description "MDF-1200-1 on South Beam"
! switchport trunk encapsulation dot1q
! switchport trunk native vlan 102
! switchport mode trunk
! NOTE: the 6248 does not support native vlan command. You can accomplish the same thing with the follwoing general mode commands.
switchport mode general
swithport general allowed vlan add a,b,c,d tagged
switchport general allowed vlan add 100 untagged
switchport general pvid 102
exit