Skip to main content
Start a Conversation

This post is more than 5 years old

Solved!

Go to Solution

krolk

160 Posts

56460

March 18th, 2013 06:00

Create 2 virtual disks in the PERC

Hi

We have PowerEdge 1950 server with HD extension PowerVault MD1000 (4.5 TB in RAID5) connecting via SCSI cables.

Howto create 2 virtual 2TB disks in the PERC?

DELL-Geoff P

990 Posts

March 18th, 2013 15:00

  1. During POST, watch for the first Ctrl-R option, hit Ctrl-R for the Perc 6/i controller:

 

  1. Hit F2 to Create a new VD

 

  1. Create the VD from this page:

 

4.Hit Enter to select RAID Level, then tab to Physical disks. With the space bar, select the drives for the

RAID level you have chosen. In this example, it’s a 3 drive RAID 5.  Tab to VD size, then tab to VD

Name and provide the name of the array. Tab again and select advanced settings, using the space

Bar . Tab down to init and use the space bar to select.  Tab to OK and enter.  This will create your

Array.

 

 

Once the array is created,  you will restart, and watch for the 2nd Ctrl-R prompt. At this prompt, you should be in the Perc 6/e controller for the external array. You will follow the same steps to create the arrays on this box.

Regards,

DELL-Geoff P

990 Posts

March 18th, 2013 07:00

Good morning.   What 2 controllers do you have installed in this server? You should have one for the internal drives, and one connected to the external array.   With this information we can further assist you.

Regards,

DELL-Geoff P

990 Posts

March 18th, 2013 09:00

Thanks.  What model are your controllers?   Perc? SAS?  They have different setups.

Regards,

krolk

160 Posts

March 18th, 2013 09:00

There are 2 controllers:

1.) for the internal drive -> 40GB

2.) for the external drive iSCSI > 4.5 TB in RAID5

We would like to cretae 2 virtal 2TB disks on the external drive.

DELL-Geoff P

990 Posts

March 18th, 2013 10:00

Thanks.  Run the following command and this will give us the information we need:

lspci -vvvnnn  

this will provide the vendor and specific information for each device.

Regards,

krolk

160 Posts

March 18th, 2013 10:00

Thx, but howto check this?

From the command line:

# lspci
00:00.0 Host bridge: Intel Corporation 5000X Chipset Memory Controller Hub (rev 12)
00:02.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 2 (rev 12)
00:03.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 3 (rev 12)
00:04.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 4-5 (rev 12)
00:05.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 5 (rev 12)
00:06.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x8 Port 6-7 (rev 12)
00:07.0 PCI bridge: Intel Corporation 5000 Series Chipset PCI Express x4 Port 7 (rev 12)
00:10.0 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev 12)
00:10.1 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev 12)
00:10.2 Host bridge: Intel Corporation 5000 Series Chipset FSB Registers (rev 12)
00:11.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev 12)
00:13.0 Host bridge: Intel Corporation 5000 Series Chipset Reserved Registers (rev 12)
00:15.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev 12)
00:16.0 Host bridge: Intel Corporation 5000 Series Chipset FBD Registers (rev 12)
00:1c.0 PCI bridge: Intel Corporation 631xESB/632xESB/3100 Chipset PCI Express Root Port 1 (rev 09)
00:1d.0 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #1 (rev 09)
00:1d.1 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #2 (rev 09)
00:1d.2 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #3 (rev 09)
00:1d.3 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset UHCI USB Controller #4 (rev 09)
00:1d.7 USB Controller: Intel Corporation 631xESB/632xESB/3100 Chipset EHCI USB2 Controller (rev 09)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d9)
00:1f.0 ISA bridge: Intel Corporation 631xESB/632xESB/3100 Chipset LPC Interface Controller (rev 09)
00:1f.2 IDE interface: Intel Corporation 31xESB/632xESB/3100 Chipset SATA Storage Controller IDE (rev 09)
01:00.0 RAID bus controller: LSI Logic / Symbios Logic LSI MegaRAID SAS 1078 Controller (rev 04)
02:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3)
03:00.0 Ethernet controller: Broadcom Corporation Broadcom NetXtreme II BCM5708 1000Base-T (rev 12)
04:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Upstream Port (rev 01)
04:00.3 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express to PCI-X Bridge (rev 01)
05:00.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E1 (rev 01)
05:01.0 PCI bridge: Intel Corporation 6311ESB/6321ESB PCI Express Downstream Port E2 (rev 01)
06:00.0 PCI bridge: Broadcom EPB PCI-Express to PCI-X Bridge (rev c3)
07:00.0 Ethernet controller: Broadcom Corporation Broadcom NetXtreme II BCM5708 1000Base-T (rev 12)
0a:00.0 PCI bridge: PLX Technology, Inc. PEX 8114 PCI Express-to-PCI/PCI-X Bridge (rev bc)
0b:08.0 SCSI storage controller: LSI Logic / Symbios Logic 53c1030 PCI-X Fusion-MPT Dual Ultra320 SCSI (rev c1)
0d:00.0 RAID bus controller: LSI Logic / Symbios Logic LSI MegaRAID SAS 1078 Controller (rev 04)
0f:0d.0 VGA compatible controller: ATI Technologies Inc ES1000 (rev 02)


krolk

160 Posts

March 18th, 2013 11:00

Here is the output:

00:00.0 0600: 8086:25c0 (rev 12)
    Subsystem: 8086:8086
    Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 16
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
        Root: Correctable- Non-Fatal- Fatal- PME-

00:02.0 0604: 8086:25e2 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=04, subordinate=09, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f2000000-f7ffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 2
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
        Root: Correctable- Non-Fatal- Fatal- PME-

00:03.0 0604: 8086:25e3 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
    I/O behind bridge: 0000e000-0000efff
    Memory behind bridge: fca00000-fcbfffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 3
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
        Root: Correctable- Non-Fatal- Fatal- PME-

00:04.0 0604: 8086:25f8 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0a, subordinate=0b, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fc500000-fc9fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot+) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 4
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
        Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
        Slot: Number 1, PowerLimit 25.000000
        Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
        Slot: AttnInd Off, PwrInd Off, Power-
        Root: Correctable- Non-Fatal- Fatal- PME-

00:05.0 0604: 8086:25e5 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0c, subordinate=0c, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 5
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x0
        Root: Correctable- Non-Fatal- Fatal- PME-

00:06.0 0604: 8086:25f9 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0d, subordinate=0d, sec-latency=0
    I/O behind bridge: 0000c000-0000cfff
    Memory behind bridge: fc300000-fc4fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot+) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 256 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 6
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x8
        Slot: AtnBtn- PwrCtrl- MRL- AtnInd- PwrInd- HotPlug- Surpise-
        Slot: Number 2, PowerLimit 25.000000
        Slot: Enabled AtnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq-
        Slot: AttnInd Off, PwrInd Off, Power-
        Root: Correctable- Non-Fatal- Fatal- PME-

00:07.0 0604: 8086:25e7 (rev 12)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=0e, subordinate=0e, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit- Queue=0/1 Enable-
        Address: fee00000  Data: 0000
    Capabilities: [6c] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 7
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x0
        Root: Correctable- Non-Fatal- Fatal- PME-

00:10.0 0600: 8086:25f0 (rev 12)
    Subsystem: 1028:01b3
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:10.1 0600: 8086:25f0 (rev 12)
    Subsystem: 1028:01b3
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:10.2 0600: 8086:25f0 (rev 12)
    Subsystem: 1028:01b3
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:11.0 0600: 8086:25f1 (rev 12)
    Subsystem: 8086:8086
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:13.0 0600: 8086:25f3 (rev 12)
    Subsystem: 8086:8086
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:15.0 0600: 8086:25f5 (rev 12)
    Subsystem: 8086:8086
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:16.0 0600: 8086:25f6 (rev 12)
    Subsystem: 8086:8086
    Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-
00:1c.0 0604: 8086:2690 (rev 09)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f8000000-fbffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] Express Root Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
        Device: Latency L0s unlimited, L1 unlimited
        Device: Errors: Correctable- Non-Fatal+ Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 1
        Link: Latency L0s <256ns, L1 <4us
        Link: ASPM Disabled RCB 64 bytes CommClk+ ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
        Root: Correctable- Non-Fatal- Fatal- PME-
    Capabilities: [80] Message Signalled Interrupts: 64bit- Queue=0/0 Enable-
        Address: 00000000  Data: 0000
    Capabilities: [90] #0d [0000]
    Capabilities: [a0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:1d.0 0c03: 8086:2688 (rev 09)
    Subsystem: 1028:01b3
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin A routed to IRQ 22
    Region 4: I/O ports at ace0

00:1d.1 0c03: 8086:2689 (rev 09)
    Subsystem: 1028:01b3
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin B routed to IRQ 23
    Region 4: I/O ports at acc0 [size=32]

00:1d.2 0c03: 8086:268a (rev 09)
    Subsystem: 1028:01b3
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin C routed to IRQ 24
    Region 4: I/O ports at aca0 [size=32]

00:1d.3 0c03: 8086:268b (rev 09)
    Subsystem: 1028:01b3
    Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin D routed to IRQ 25
    Region 4: I/O ports at ac80 [size=32]

00:1d.7 0c03: 8086:268c (rev 09) (prog-if 20)
    Subsystem: 1028:01b3
    Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin A routed to IRQ 22
    Region 0: Memory at fcc00400 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Debug port

00:1e.0 0604: 8086:244e (rev d9) (prog-if 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0
    Bus: primary=00, secondary=0f, subordinate=0f, sec-latency=32
    I/O behind bridge: 0000b000-0000bfff
    Memory behind bridge: fc100000-fc2fffff
    Prefetchable memory behind bridge: 00000000d8000000-00000000dff00000
    Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
    Capabilities: [50] #0d [0000]

00:1f.0 0601: 8086:2670 (rev 09)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0

00:1f.2 0101: 8086:2680 (rev 09) (prog-if 8f)
    Subsystem: 1028:01b3
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR- FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 0
    Interrupt: pin C routed to IRQ 26
    Region 0: I/O ports at ac78 [size=8]
    Region 1: I/O ports at ac70 [size=4]
    Region 2: I/O ports at ac60 [size=8]
    Region 3: I/O ports at ac58 [size=4]
    Region 4: I/O ports at ac40 [size=16]
    Region 5: Memory at fcc00000 (32-bit, non-prefetchable) [size=1K]
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 0104: 1000:0060 (rev 04)
    Subsystem: 1028:1f0c
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 31
    Region 0: Memory at fcb80000 (64-bit, non-prefetchable) [size=256K]
    Region 2: I/O ports at ec00 [size=256]
    Region 3: Memory at fcb40000 (64-bit, non-prefetchable) [size=256K]
    Expansion ROM at fca00000 [disabled] [size=32K]
    Capabilities: [b0] Express Endpoint IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: AtnBtn- AtnInd- PwrInd-
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 256 bytes, MaxReadReq 2048 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
        Link: Latency L0s <2us, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [c4] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [d4] MSI-X: Enable- Mask- TabSize=4
        Vector table: BAR=0 offset=0003e000
        PBA: BAR=0 offset=00fff000
    Capabilities: [e0] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [ec] Vital Product Data

02:00.0 0604: 1166:0103 (rev c3)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=02, secondary=03, subordinate=03, sec-latency=64
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f8000000-fbffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-     BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0
        Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
        Device: Latency L0s <64ns, L1 <1us
        Device: AtnBtn- AtnInd- PwrInd-
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
        Link: Latency L0s <4us, L1 <4us
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [90] PCI-X bridge device
        Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
        Status: Dev=02:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
        Upstream: Capacity=0 CommitmentLimit=0
        Downstream: Capacity=0 CommitmentLimit=0
    Capabilities: [b0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-

03:00.0 0200: 14e4:164c (rev 12)
    Subsystem: 1028:01b3
    Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 32 (16000ns min), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 35
    Region 0: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
    Capabilities: [40] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=8
        Status: Dev=03:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
    Capabilities: [48] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    Capabilities: [50] Vital Product Data
    Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
        Address: 00000000fee00000  Data: 0091

04:00.0 0604: 8086:3500 (rev 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=04, secondary=05, subordinate=08, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f4000000-f7ffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [44] Express Upstream Port IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s <64ns, L1 <1us
        Device: AtnBtn- AtnInd- PwrInd-
        Device: SlotPowerLimit 0.000000
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] #0d [0000]

04:00.3 0604: 8086:350c (rev 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=04, secondary=09, subordinate=09, sec-latency=64
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=medium >TAbort-     BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [44] Express PCI/PCI-X Bridge IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s <64ns, L1 <1us
        Device: AtnBtn- AtnInd- PwrInd-
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 256 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [6c] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] #0d [0000]
    Capabilities: [d8] PCI-X bridge device
        Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
        Status: Dev=00:00.3 64bit- 133MHz- SCD- USC- SCO- SRD-
        Upstream: Capacity=65535 CommitmentLimit=65535
        Downstream: Capacity=65535 CommitmentLimit=65535

05:00.0 0604: 8086:3510 (rev 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=05, secondary=06, subordinate=07, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f4000000-f7ffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s <64ns, L1 <1us
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] #0d [0000]

05:01.0 0604: 8086:3514 (rev 01)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=05, secondary=08, subordinate=08, sec-latency=0
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: fff00000-000fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-     BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
    Capabilities: [44] Express Downstream Port (Slot-) IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s <64ns, L1 <1us
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 4096 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s, Port 0
        Link: Latency L0s unlimited, L1 unlimited
        Link: ASPM Disabled Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x0
    Capabilities: [60] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [70] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [80] #0d [0000]

06:00.0 0604: 1166:0103 (rev c3)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Bus: primary=06, secondary=07, subordinate=07, sec-latency=64
    I/O behind bridge: 0000f000-00000fff
    Memory behind bridge: f4000000-f7ffffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort-     BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [60] Express PCI/PCI-X Bridge IRQ 0
        Device: Supported: MaxPayload 128 bytes, PhantFunc 0, ExtTag+
        Device: Latency L0s <64ns, L1 <1us
        Device: AtnBtn- AtnInd- PwrInd-
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 128 bytes, MaxReadReq 128 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
        Link: Latency L0s <4us, L1 <4us
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4
    Capabilities: [90] PCI-X bridge device
        Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
        Status: Dev=06:00.0 64bit- 133MHz- SCD- USC- SCO- SRD-
        Upstream: Capacity=0 CommitmentLimit=0
        Downstream: Capacity=0 CommitmentLimit=0
    Capabilities: [b0] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-

07:00.0 0200: 14e4:164c (rev 12)
    Subsystem: 1028:01b3
    Control: I/O- Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 64 (16000ns min), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 30
    Region 0: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
    Capabilities: [40] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=8
        Status: Dev=07:00.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
    Capabilities: [48] Power Management version 2
        Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
        Status: D0 PME-Enable- DSel=0 DScale=1 PME-
    Capabilities: [50] Vital Product Data
    Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable+
        Address: 00000000fee02000  Data: 0099

0a:00.0 0604: 10b5:8114 (rev bc)
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Region 0: Memory at fc5fe000 (32-bit, non-prefetchable) [size=8K]
    Bus: primary=0a, secondary=0b, subordinate=0b, sec-latency=0
    I/O behind bridge: 0000d000-0000dfff
    Memory behind bridge: fc700000-fc9fffff
    Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
    Secondary status: 66MHz+ FastB2B+ ParErr- DEVSEL=slow >TAbort-     BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
    Capabilities: [40] Power Management version 3
        Flags: PMEClk+ DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [48] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [58] PCI-X bridge device
        Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=133MHz
        Status: Dev=0a:00.0 64bit- 133MHz- SCD- USC- SCO+ SRD-
        Upstream: Capacity=16 CommitmentLimit=16
        Downstream: Capacity=16 CommitmentLimit=16
    Capabilities: [68] Express PCI/PCI-X Bridge IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s <64ns, L1 <1us
        Device: AtnBtn+ AtnInd+ PwrInd+
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
        Device: MaxPayload 256 bytes, MaxReadReq 512 bytes
        Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
        Link: Latency L0s <2us, L1 <32us
        Link: ASPM Disabled CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x4

0b:08.0 0100: 1000:0030 (rev c1)
    Subsystem: 1000:50c0
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 72 (4000ns min, 1500ns max), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 33
    Region 0: I/O ports at dc00 [size=256]
    Region 1: Memory at fc8e0000 (64-bit, non-prefetchable) [size=128K]
    Region 3: Memory at fc8c0000 (64-bit, non-prefetchable) [size=128K]
    Expansion ROM at fc900000 [disabled] [size=1M]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [68] PCI-X non-bridge device
        Command: DPERE- ERO- RBC=512 OST=8
        Status: Dev=0b:08.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=2048 DMOST=8 DMCRS=16 RSCEM- 266MHz- 533MHz-

0d:00.0 0104: 1000:0060 (rev 04)
    Subsystem: 1028:1f0a
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- SERR-     Latency: 0, Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 34
    Region 0: Memory at fc480000 (64-bit, non-prefetchable) [size=256K]
    Region 2: I/O ports at cc00 [size=256]
    Region 3: Memory at fc440000 (64-bit, non-prefetchable) [size=256K]
    Expansion ROM at fc300000 [disabled] [size=32K]
    Capabilities: [b0] Express Endpoint IRQ 0
        Device: Supported: MaxPayload 256 bytes, PhantFunc 0, ExtTag-
        Device: Latency L0s unlimited, L1 unlimited
        Device: AtnBtn- AtnInd- PwrInd-
        Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
        Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
        Device: MaxPayload 256 bytes, MaxReadReq 2048 bytes
        Link: Supported Speed 2.5Gb/s, Width x8, ASPM L0s, Port 0
        Link: Latency L0s <2us, L1 unlimited
        Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
        Link: Speed 2.5Gb/s, Width x8
    Capabilities: [c4] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable-
        Address: 0000000000000000  Data: 0000
    Capabilities: [d4] MSI-X: Enable- Mask- TabSize=4
        Vector table: BAR=0 offset=0003e000
        PBA: BAR=0 offset=00fff000
    Capabilities: [e0] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [ec] Vital Product Data

0f:0d.0 0300: 1002:515e (rev 02)
    Subsystem: 1028:01b3
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR+ FastB2B-
    Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- SERR-     Latency: 32 (2000ns min), Cache Line Size: 64 bytes
    Interrupt: pin A routed to IRQ 36
    Region 0: Memory at d8000000 (32-bit, prefetchable) [size=128M]
    Region 1: I/O ports at bc00 [size=256]
    Region 2: Memory at fc2d0000 (32-bit, non-prefetchable) [size=64K]
    [virtual] Expansion ROM at fc100000 [disabled] [size=128K]
    Capabilities: [50] Power Management version 2
        Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
        Status: D0 PME-Enable- DSel=0 DScale=0 PME-


krolk

160 Posts

March 20th, 2013 05:00

Thx a lot, I've created virtual disks using Perc and it works well now.

View More

View All

No Events found!

Top