Upgrade RAM PowerEdge Dell T110 II

Hi Marko,

The T110 II takes UDIMMs and the NT8GC72B4NB1NJ-CG are RDIMMs. Page 86 of the user guide contains the section on memory. 

• 2Gb DRAM technology
• Supports 2 channels per processor
• Supports Un-buffered (UDIMM) ECC DDR3 DIMMs.
• DDR3 speeds of 1333 and 1600 (with Ivy Bridge Processor) supported
• Single Rank and Dual Rank UDIMMs supported
• No RDIMM support
• Low-voltage(LV) DIMM supported @ 3.5V only
• Non-ECC DIMMs are not supported
• Support for up to 32GB UDIMM memory (with 4 x 8GB UDIMMs)
• No support for quad rank DIMMs
• Single DIMM configuration only with DIMM in socket A1

Please send a private message with your service tag to ensure we have all appropriate information on your system.

Thank you,

Hi Jim,

thank you for the reply.

So i have to check this information about the Ram, it must be:

-ECC

-UDIMM

-DDR3 speeds of 1333 and 1600

-Unbuffered

-1.35V or 1.5V

the important thing that has these specifications right?

Thanks,

Marko

Hi Marco,

You are correct. Let me know if you need anything else.

Hi Jim,

thank you for your reply. I tried to upgrade with module CRUCIAL CT102464BD160B but doesnt work.

This RAM is UDIMM, Unbuffered, ECC, DDR3...

Thanks in advance for reply.

Marco

Hi Marco,

That DIMM is non-ECC and is not supported. Needs to be ECC. 

Crucial 8GB DDR3L-1600 UDIMM
CT102464BD160B
 
Brand: Crucial
Form Factor: UDIMM
Total Capacity: 8GB
Warranty: Limited Lifetime
Specs: DDR3 PC3-12800 • CL=11 • Unbuffered • NON-ECC • DDR3-1600 • 1.35V • 1024Meg x 64 •
Series: Crucial

Hi,

Unfortunately, HMT31GR7CFR4C is another RDIMM and will not work. Need to use UDIMM.

The Dell part number that will work is 96MCT.

Please let me know if you need anything else.

Hi Jim,

do you think that memory "Dell SNPX3R5MC/8G X3R5M" could be fine for my server DELL T110 II?

Below a photo of this bank.

Thanks in advance.

We like to use Crucials memory tool:

http://www.crucial.com/usa/en/poweredge-t110-ii/CT2892159

Thanks,

Mark

Hello Jimmy, Thanks for the comment. We have a similar challenge where the same  server model currently has two (2) memory cards, each 2gb in size with the model details: 2gb 1Rx8 PC3L 10600E 

However, we want to replace them with two (2) 8gb memory cards. Unfortunately this has not been successful. 

The server details are as follows:

MODEL: PowerEdge T110 II, E11S

SERVICE TAG:

EXPRESS SERVICE TAG: 

Kindly advise on which memory card details with 4gb or 8gb will work please.

Hello,

There are a few 8GB DIMM part numbers at that same speed. You can try KTXN3, KF4D0, and FDFM2. These parts are DIMMs that have been validated for the server and operate at the same frequency as your current DIMMs.

Thanks Mr Moderator,

I want to thank you for the great response. To purchase the memory cards, i will very grateful to assist with a few urls where i can purchase the recommended specification for the server.

Thanks in advance.

Hi,

you might check our Partner search portal:

http://dell.force.com/?c=us&l=en&pt=findadistributor

Or search on any search engine for "Dell" + the part number. This might bring up some more resellers.

Best regards,
Stefan