Smcli revive diskPool command not available

Dell-Sam L (nice name btw),

Thanks for the response.

Drives are all in an optimal state and ready for the pools to be revived.  What I am reporting is a deficiency in SMcli and that the command SMcli -n -c "revive diskPool[pool_name]" doesn't exist.  And what I am asking is, is there another way to revive a disk pool.

--Sam

Hello Sam,

Remove tray_name from your syntax.  You want it to be like this.

smcli -n -c "revive diskPool [diskPoolName]"

Please let us know if you have any other questions.

Hello Sam, have you been able to make it work?

I have same issue:

• MD3220i, controllers firmware 08.20.24.60
• MDSS 6.5.0.1

SMcli 10.0.0.102 -c "revive diskPool [dp1];"  
Performing syntax check...  

Encountered "diskPool" at line 1, column 23.  
Was expecting one of:

"physicalDisk" ...
"diskGroup" ...
"snapGroup" ...
"cgMemberVirtualDisk" ...
"snapVirtualDisk" ...

SMcli failed.

Thanks for helping!

Hello Alex,

You have a semi colon in your syntax that should be there.  You want to use the following command:

SMcli 10.0.0.102 -c "revive diskPool [dp1]"

That should fix your issue and allow the command to complete successfully.

Please let us know if you have any other questions.

Please i have 2 disk group failed after power problem in our Dell MD3200i and MD1200.

i can't find the correct smcli commande to revive disk. 

Hello Chafik Hammami,

Here is the link to the SMCLI guide and if you look on page 273, & it list the revive disk group command. https://topics-cdn.dell.com/pdf/powervault-md3200_cli-guide_en-us.pdf  

Please let us know if you have any other questions.

I am getting the same error on MD3800i

all disks are optimal but our pool has failed from a power failure no matter which way i i try the revive command

Any help much appreciated as cluster is in failed state

Hello, I am having an issue where a disk pool is showing failed after a power outage. Please help me I will do anything. 

I have tried the CLI but get the same error as everyone else. 

Hi @tonythedev,

I'll work with you on your newly posted topic here: https://dell.to/3LkwKSW to avoid any confusion.

Hi. We have the same problem with diskpool as tonythedev had.

Is it possible someone from Dell to help us?

We have MD3800i, plus two disk enclosures - MD1220.

After power failure one of the disk enclosures (MD1220) crashed.

We had one diskpool and one diskgroup on this enclosure. We restored one diskgroup from SMcli by "revive diskgroup" command successfully. But we are unable to restore diskpool.

We are getting the following answer:

Encountered "diskpool" at line 1, column 8.
Was expecting one of:
    "physicalDisk" ...
    "diskGroup" ...
    "snapGroup" ...
    "cgMemberVirtualDisk" ...
    "snapVirtualDisk" ...

SMcli failed. 

It seems command "revive diskpool" is not available in my Cli :(

Any help would be appreciated!

Hello,

Could you pull an support report and upload for us to get a look?

How to gather Support Information MD3xxx https://dell.to/3yimkPc

You can upload here under the case number that I will send you in a private message.

https://dell.to/4b6mI1P

Hey there,

have the same issue, also after Power failure! The revive diskPool command seems not to exist. hat anyone the chance to fix that? I tryed it via telnet aswell, but that seems to be a different shell!?

Help is very much appreciated! Thanks in advance

Tobias

Hi,

Please make sure there are no syntax errors in your command. For example, try removing any unnecessary semicolons or spaces

Syntax

revive diskPool [
                                 diskPoolName]
                              

Parameter

@DELL-Erman O​ 

No Typos, only the message!