Unsolved
This post is more than 5 years old
18 Posts
0
1383
Host HBA is not logging in on the Symmetrix
I'm experiencing issues while connecting devices to a RHEL5.5 host.
One path is not visible, while the other one is.
- I have mapped the devices to FA 7c1 and 10c1
- Host WWN's are: 5001438004c1d608 ; 5001438004c1d60a
- Host is a c-blade in an enclosure with more hosts that have SAN connection. Blade enclosure should not be an issue.
- emcgrab on the host came back with no issues.
- HBA and FA are zoned properly; Devices over FA 7c1 are visible on the host. Devices over FA 10c1 are not.
- fcping for FA 10c1 reports back:
switchfc2:admin> fcping 50:01:43:80:04:c1:d6:0a 50:06:04:8c:52:a7:c9:29
Source: 50:01:43:80:04:c1:d6:0a
Destination: 50:06:04:8c:52:a7:c9:29
Zone Check: Zoned
Pinging 50:01:43:80:04:c1:d6:0a [0x1c0400] with 12 bytes of data:
received reply from 50:01:43:80:04:c1:d6:0a: 12 bytes time:583 usec
---
5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout
Round-trip min/avg/max = 583/684/901 usec
Pinging 50:06:04:8c:52:a7:c9:29 [0x63f00] with 12 bytes of data:
received reply from 50:06:04:8c:52:a7:c9:29: 12 bytes time:856 usec
---
5 frames sent, 5 frames received, 0 frames rejected, 0 frames timeout
Round-trip min/avg/max = 834/901/992 usec
- Masking is correct:
Symmetrix ID : 000290102064
Device Identifier Type Dir:P
------ ---------------- ----- ----------------
00ED 5001438004c1d608 FIBRE FA-7C:1
5001438004c1d60a FIBRE FA-10C:1
00F5 5001438004c1d608 FIBRE FA-7C:1
5001438004c1d60a FIBRE FA-10C:1
00FD 5001438004c1d608 FIBRE FA-7C:1
5001438004c1d60a FIBRE FA-10C:1
0105 5001438004c1d608 FIBRE FA-7C:1
5001438004c1d60a FIBRE FA-10C:1
QLA tools on the host reports back:
QLogic HBA-Snapshot Utility.
QLogic HBA Host0 Information
WWPN: 0x5001438004c1d608
WWNN: 0x5001438004c1d609
Driver Version: 8.03.01.04.05.05-k
Model: QMH2462
Firmware Version: 5.03.02 (496)
Link State: Link Up - F_Port
Device Information
Device : 0
Vendor: Unknown
Model: Unknown
WWPN: 0x5006048c52a6cc26
Port ID: 0x04a400
Number of LUNs: 42
QLogic HBA Host1 Information
WWPN: 0x5001438004c1d60a
WWNN: 0x5001438004c1d60b
Driver Version: 8.03.01.04.05.05-k
Model: QMH2462
Firmware Version: 5.03.02 (496)
Link State: Link Up - F_Port
- Symmetrix is a DMX3-4500
- Port flag setting of both FA ports are identical. Due to the fact one path is working, this should not be problem.
I am pretty fresh out of idea's of what could be going on here..
Are there things I missing here?
mamer1
18 Posts
0
September 15th, 2011 03:00
Well everybody, let's pretend I didn't asked this....
I need to read more carefully.
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
September 15th, 2011 05:00
did you resolve your issues ..what was the problem ?
mamer1
18 Posts
0
September 15th, 2011 05:00
The WWN zoned was of the FA port of the wrong symm.
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
September 15th, 2011 05:00
Oops , honest mistake
SKT2
2 Intern
2 Intern
•
1.3K Posts
0
September 15th, 2011 17:00
is this a Brocade or Cisco environment?