Unsolved
This post is more than 5 years old
26 Posts
0
6584
Help with DR setup for VMware 5.5 environment
Hello,
We are looking to setup a primary site where we will have 4-5 VMWare hypervisors utilizing a VNX5400. We would like to have the VMs LUN/s replicate to an offsite DR running the same hardware as described above. Setup would be HOT/COLD, where we would fully cut over all of the VMs from the PRIMARY SITE to the DR SITE.
We currently have purchased the following software:
For Hypervisor enviroment:
VMWare vSphere Std with Operation Manager
Storage Array:
VNXB OE PER TB PERFORMANCE
VNX522 Unisphere Block Suite
VNX5200 FAST Suite
VNX5200 Local Protection Suite
VNX5200 Remote Protection Suite
Questions we have are:
Does the software described above allow us the ability we are looking for?
Any input would really appreciated.
Thanks
joe
joe_cole1
26 Posts
0
February 18th, 2015 13:00
Little light bulb over my head lit up when I read your last breakdown. I really appreciate the help.
On the VNX unit, I will have to setup another iSCSI interface just for the vRPA connections? If so, would that require 2 interfaces since i see that vrpa setup is asking for two iSCSI networks?
joe_cole1
26 Posts
0
February 28th, 2015 23:00
here's a quick update.
I have both vRPAs deployed per site and configured according to install details. However, I am seeing the following error when trying to connect one cluster to the other.
Fetching remote certificate
Internal error. Failed getting remote certificate: Socket is closed
I confirmed that i can ping both WAN IPs from both sites, and vice verse.
Any advice or directions will be truly appreciated.
brettesinclair
2 Intern
2 Intern
•
715 Posts
0
March 1st, 2015 00:00
Looks like you have progressed pretty well to this point.
Have you opened up the required firewall ports between the two sites as per the security guide ?
There's numerous ports required for both tcp and udp, so you may find it easier to open up all ports between the RPA's at either side of the WAN, but this will depend on your policy.
1 Attachment
Security Configuration Guide 4.1 - 302-001-157_02.pdf
joe_cole1
26 Posts
0
March 1st, 2015 12:00
Would it be possible to provide the security guide?
Thanks
brettesinclair
2 Intern
2 Intern
•
715 Posts
0
March 1st, 2015 13:00
It's attached to my last post, and linked below;
https://support.emc.com/docu54073_RecoverPoint_4.1_Security_Configuration_Guide.pdf?language=en_US
joe_cole1
26 Posts
0
March 1st, 2015 15:00
Sorry about that, I didn't notice the attachment since I replied via my phone. I'll definitely take a look at this and hopefully resolve this issue. Once again, thanks for all the help.
joe_cole1
26 Posts
0
March 1st, 2015 18:00
just for a sanity check.
I have deployed 2 vRPA at each site. I tried to use the GUI deployment manager but would get some errors. Not sure if I was typing in something wrong or what, however I decided to do the setup via ssh to each vRPA. I was able to configure both vRPAs with appropriate networks and connectivity to the SAN at each site.
Now just to make sure, those two vRPAs are now a cluster on each site correct? If so, the next step would be to connect site A cluster to site B via WAN connection correct?
I was looking over the security config guide but could not find any more information on network requirements such as layer 2 vs layer 3 . We are using xVLAN for the WAN network, but not sure if this is what might be the issue.
arali0
1 Message
0
February 26th, 2016 07:00
Hi Joe,
Can you please tell me,how you have solved below issue.
Fetching remote certificate
Internal error. Failed getting remote certificate: Socket is closed