UNSOLVED

Narnia Nitro

updated

21 years ago

0

8556

September 1st, 2005 02:00

Boot up problem

I have a Dimension 2400 that I bought in 2003.  Today I try to boot it up (it had been working fine beforehand) and after about two seconds the light on the CD-R drive begins blinking about once a second, as does the harddrive.  The computer does not get past that point in the boot up.  I've since tried to power down for a time before powering back up, but the problem remains.
 
I've opened the CD-R drive and removed the CD that had been in there.  Still does not help. 
 
I remember having this same problem about a month ago, and I can't remember how I solved it to get my computer boot up regularly again.  But it goes to show that I should be able to fix the thing. 

Can anyone help?
  • shesagordie

    12 Elder

    •

    46017 Posts

    428

    0

    Posted September 1st, 2005 03:00

    Narnia Nitro.
     
    What is the reading of the power button LED, green, blinking green, solid amber, blinking amber?
    What is the sequence of the diagnostic LEDs at the back of the case?
     
     
    Bev.
     
     
  • 428

    0

    Posted September 1st, 2005 15:00

    Hi Bev.
     
    The LED is a steady green light when I try to boot up.  The CD-R light is blinking regularly, and the harddrive light also blinks regularly when I try to boot up.  It's almost as if it's caught in some sort of loop that it can't break out of.
     
    Thanks,
     
    NN
  • shesagordie

    12 Elder

    •

    46017 Posts

    428

    0

    Posted September 1st, 2005 17:00

    Narnia Nitro

    What is the sequence of the diagnostic LEDs at the back panel of the case?

    Bev.

     

  • 428

    0

    Posted September 2nd, 2005 15:00

    Bev,
     
    Unfortunately I can't answer that question now because my computer won't turn on!  I'm mentioning it here because it might be related to the other problem I'm having.
     
    Basically, when I unplug the computer and then plug it back in, the computer doesn't turn on right away.  Instead, after some time, it warms up and I get the blinking amber light.  This has been happening for some months now, and usually after the amber light blinks for some time (maybe 5 mins or so) the computer boots up normally. 

    This time, however, I've let the amber light blink for a long time, and it still doesn't boot up.  I've found a few posts in this forum which suggest that it could be a bad power supply unit or something like that.  I'm hoping that the computer will eventually boot up as normal, or even to the point that I was getting to before where it would begin to power up before looping.  Right now, there are no diagnostic LEDs on the back that light up. 
  • shesagordie

    12 Elder

    •

    46017 Posts

    428

    0

    Posted September 2nd, 2005 20:00

    Narnia Nitro.
     
    Yes, it could be the power supply.
     
    Try testing it, by unplugging the 20 pin connector from the motherboard and jumping the Green wire to one of the Black wires, if power supply and/or case/processor fans run, then you know it's good.
     
    As it's D-2400 and has an open back panel, if your system is not under warranty, you can use most generic ATX PSUs with or without the on/off power switch. Check out the Antec power supply line.

    Bev.
  • 428

    0

    Posted September 5th, 2005 18:00

    Alright, my computer just magically turned on again...somehow I got power, just as I'm reading through the posts about changing the PSU.  However, it's still skipping and won't boot up normally.
     
    Anyway, to answer your previous question, the LED lights on the back:
     
    all of them A-B-C-D are flashing at the same time.  A and B lights flash amber, but after a split second the A light turns green.  C and D lights flash green. 
     
    The harddrive or something sounds like it's still looping.
     
    Thanks for any additional help.
  • 428

    0

    Posted September 5th, 2005 19:00

    By the way, I looked in the dell manual and saw that when A/B are yellow, C/D are green, it means a memory module problem.  So, I have tried to take one out and leave the other in, and I even tried to replace one with the other, but to no avail.  I also unplugged power to the CD-R since I thought that might be the problem.  Well, it still isn't working.  I also took out a wireless card from a PCI slot, but that didn't help. 
     
    I'm beginning to really wonder what the problem is.