
UNSOLVED
D
dwagner3210
9 Posts
0
17605
September 18th, 2008 17:00
Dimension 3000 Power problem
Have looked at other posts and think I have my conclusion but wanted to make sure I was not missing something as I literally just reloaded this machine about a month ago after HD went bad making us 4 for 4 with Dimension 3000 machines we bought!
Hit power switch CD lights flash and then nothing. Green LED on MB is on steady. Have taken all PCI cards out and detached all drives. Same result. No beeps if I try to boot with all memory removed and bare MB.
Jumpered Green and black on power supply - fan comes on.
I saw one post where person tried new PS and got some error lights that in the end said MB fried.
I think my MB is fried as well. Any last thoughts?
Responses (10)
Solutions (0)
dwagner3210
9 Posts
680
0
Posted September 18th, 2008 21:00
mac_lover thx for reply
As far as lights. Mother board is LED is solid green. Strange thing though now. The power light is amber.
There are no diagnostics lights on.
Also the other 3 Dimensions are being used.
So I am not sure those folsk would like me "borrowing" their PS ;-)
shesagordie
12 Elder
•
46017 Posts
680
0
Posted September 18th, 2008 23:00
dwagner3210
Is the power button LED, blinking amber, or solid amber?
The D-3000 troubleshooter is here
Bev.
===================================================
Please don't send me questions about your system by DCF Messenger.
Post the issue in the appropriate Board, where they will be answered.dwagner3210
9 Posts
680
0
Posted September 19th, 2008 00:00
solid amber. i will try to see if one of the cards or memory is bad. that would be less hassle than MB replace!
Thanks will keep you posted.
shesagordie
12 Elder
•
46017 Posts
680
0
Posted September 19th, 2008 02:00
dwagner3210
If checking the memory and the cards does not resolve the problem and you are comfortable around computers, you could try the following:
Remove the power cord, hold power button in for several seconds to discharge the residue power.
Remove all the PCI cards, the video card [if applicable], memory, all peripherals, disconnect the data and power cables to all the drives, check that the front panel cable is connected to motherboard, with nothing else connected to the system, reconnect the power cable and power the system on.
If you do not get any beep codes or diagnostic lights on the back panel, then it would appear that motherboard has died.
Bev.
===================================================
Please don't send me questions about your system by DCF Messenger.
Post the issue in the appropriate Board, where they will be answered.dwagner3210
9 Posts
680
0
Posted September 21st, 2008 21:00
Ok finally got a chance to play with this again.
Removed all cards, disconnected all data and power cables, removed all memory - pushed start button and sometime lights power lights flashed briefly and then went out and other times when I pushed they would stay on solide amber and solid green. No beep codes in either scenario. I assume it is MB based on that but any chance switch is bad??
also no diagnostic lights ever come on.
one thing i also did was remove all cards and still had HD, floppy and CD/dvd drives hooked up, also had memory in. when i did this it would go to solid amber light and solid green light. fan on PS was turning. would stay that way for about ten seconds and then go dead. again no beep codes and no diagnostic lights.
dwagner3210
9 Posts
680
0
Posted September 24th, 2008 20:00
Well replaced mother board and i am right back where I started. Solid Amber light, no diagnostic lights, no boot.
I went back through the other stuff reomoving cards to troubleshoot amber light - with all cards removed still amber light onn.
Reseated memory with all cards out still amber.
Removed all memeory no beep codes.
Any thoughts.
dwagner3210
9 Posts
680
0
Posted September 25th, 2008 16:00
installed new psu (430W Thermaltake for $30) and voila pc works. I am going to tell myself the motherboard was bad as well originally so that I do have to swap out and deal with return.
As a side note, getting the new MB was an incredible ordeal. Original call was "we have to check on stock since only 3 left. we will get back to you in 4-24 hours" After 72 hours I called 3x to finally get someone that could get me right part. First 2 wanted to sell me MB ranging in price from $260 to $370. I laughed and told them I could almost buy a new PC for that price. They said that they had plenty of those boards though. At that price they probably will be there a while. I finally got a board NG368 ($112)and it worked great. A little shorter than original but easy install.
Thanks for your help.
shesagordie
12 Elder
•
46017 Posts
111
0
Posted September 25th, 2008 21:00
dwagner3210
Happy to hear that the problem is resolved.
Wow, $260/370 for a motherboard, someone is living in 'Cloud-Cuckoo-Land'.
Bev.
===================================================
Please don't send me questions about your system by DCF Messenger.
Post the issue in the appropriate Board, where they will be answered.

mac_lover
15 Posts
680
0
Posted September 18th, 2008 18:00
yup! your MB needs replacement.