UNSOLVED
Error code 10 - NIC
I m using dell laptop 600m.
My onboard network card (Broadcom) is showing a "!" with error code 10.
What I did:
1) I reinstalled the driver several times and check through any hidden divices that present.
2) I re-installed the windows xp home (by upgrading). Scan disk countless with chkdsk command and several other utilities. I ran the net diagnostic, of course it also failed.
3) Scanned for virus. It scanned a virus so call svchost.exe and guess it has been deleted.
The odd thing is that the NIC is loded fine with no problem in device manager and the little window present on the taskbar, but it has no respond (no light) when I plug in the cable. Then, when I restart the comp and the code 10 came back.
It has respond by pinging 127.0.0.1 but not any other. TTL replied was just 64 instead of 128 last time
My onboard network card (Broadcom) is showing a "!" with error code 10.
What I did:
1) I reinstalled the driver several times and check through any hidden divices that present.
2) I re-installed the windows xp home (by upgrading). Scan disk countless with chkdsk command and several other utilities. I ran the net diagnostic, of course it also failed.
3) Scanned for virus. It scanned a virus so call svchost.exe and guess it has been deleted.
The odd thing is that the NIC is loded fine with no problem in device manager and the little window present on the taskbar, but it has no respond (no light) when I plug in the cable. Then, when I restart the comp and the code 10 came back.
It has respond by pinging 127.0.0.1 but not any other. TTL replied was just 64 instead of 128 last time
Tried the command ipconfig/all....just reply in a single phrase: something like windows IP configuration.
Pls help, I m completely lost on this.
Thanks,
Pls help, I m completely lost on this.
Thanks,
Hi BBraxton,
I did some modification to change some services under services.msc. What I did is just change some services from "auto start" to "manual" follow this computer which I can access internet here.
I then restart my notebook and guess wht, the little LAN twin windows appeared on the taskbar.
I then did what u told and the finding as below:
Media state : Disconnected
Host name : ssspring-L
Primary DNS suffix : "blank"
Mode type : Hybrid
IP Routing Enabled : No
Wins Proxy Enabled : No
Ethernet adapter LAN
Media state : Media disconected
Description : Broadcom 570x Gigabit Integrated Controller
Physical address : 00-0F-1F-BC-B3-F1
To double confirm it work, I then restarted the notebook again, but strangely, it turned back with code 10 and the twin window disappeared, no matter how many time I restarted again.
What happen??
Under registry, I did found that it detected my NIC. Confuse :smileysurprised:
After some working, my little windows finally came out consistently...i guess....:p
But when I plug in a known working cable, the light doesn't light up and the windows remain disconnect.
Any idea what is the problem? Hardware failure or setting? I can ping 127.0.0.1 with reply TTL = 128 now.
Thanks!
- Hi BBraxton,It's i year plus since I bought, but i don't have the access of wireless activity here.What I found when I try troubleshoot again last nite:1) ipconfig /all command:Windows IP Configuration
Host name: ssspring
Primary DNS suffix:
Mode type: Hybrid
IP Routing Enabled: No
Wins proxy enabled: NoEthernet adapter local area network 3
Media state: Media disconnected
Description: Broadcom 570x Gigabit Intergrated Controller
Physical address: 00-0F-1F-BC-D3-F1Tunnel adapter Teredo Tunneling Pseudo-Interface (<---previously none, no idea of this??)
Connection-specific DNS suffix:
Description: Teredo Tunneling Pseudo-Interface
Physical address: FF-FF-FF-FF-FF-FF-FF-FF
Dhcp Enabled: No
IP address: fe80::5545:5245:444f%5
Default gateway:
Netbios over Tcpip: Disabled2) Broadcom Diagnostic Control SuiteDevice detected w/out problem and all the below tests past:Control registers
Mill registers
E E Prom
Internal memory
On chip CPU
Interuppt
Loopback - MAC
Loopback - PHY
Test LED3) Ping IP which I set manually (10.1.1.5) not successful.4) Why there are two network icons in my control panel??Please help, totally confused :smileysad:
BBraxton
2 Intern
•
2037 Posts
497
0
Posted May 24th, 2006 11:00
This gives you a plain black Command window and a drive letter. Type the following, ending each with
press Enter
which is an action, not actual type letters:
C:
CD \
MD \DOWNLOAD
CD \DOWNLOAD
IPCONFIG /ALL >My.txt
EXIT
There is a considerable pause after the >My.txt line because instead of displaying the test, this command is re-writing the report to a txt file in the DOWNLOAD folder.
'Exit' lets you out of the black Command window.
Now Start | Run 'Notepad'
Do an 'Open' to the DOWNLOAD folder to the file My(.txt) and you will see and can copy the full report, pasting it in your DellTalk thread.
Message Edited by BBraxton on 05-24-200607:39 AM