UNSOLVED

kgoodman54

updated

19 years ago

0

39534

December 12th, 2007 17:00

Boot Up Stops after POST

This is a Power Edge 1600SC server using Windows Server 2003. Every time the server goes down or is rebooted following a Microsoft Update, the POST runs and stops saying Press F1 to continue or F2 to change settings. It will not go beyond this until you press F1. Two other servers running identical software (HP-Compaq) continue on and load the operating software and continue running. My 1600SC sits until the problem is discovered and someone presses F1. This is not deadly, but very annoying. I have looked in the knowledge base and cannot find any solutions or settings in BIOS the would cause this stop. Any ideas. Thanks!
  • at5147

    884 Posts

    1406

    0

    Posted December 12th, 2007 17:00

    Check in Hard-Disk Drive Sequence and Boot Device to make sure that the RAID controller and Hard-disk C are first.
  • 1406

    0

    Posted December 13th, 2007 12:00

    Thanks for your response:
    I have checked the Boot Device (in setup) and it was
    1. Default drive A:
    2. Hard disk drive C:
    Those were my only options. Could not add devices. I switched the order and got the same thing.
    HDD Sequence was
    1. System BIOS boot device
    2. Slot 1:PERC 4/SC Adapter (bus 01 dev 02)
    I was unable to add or change these
     
    The entire POST runs and loads all adapters and devices but then the last line still says:
     
    "Press F1 to continue or F2 to run configuration utility."  After you press F1 Windows 2003 Server loads fine, BUT, every boot, you MUST press F1, it will not automatically go around this action and load Windows 2003 Server.
  • at5147

    884 Posts

    1406

    0

    Posted December 13th, 2007 17:00

    Move Hard disk drive C: and Slot 1 PERC 4/SC Adapter (bus 01 dev 02) to the first spot and save change and exit.
  • 1406

    0

    Posted December 16th, 2007 14:00

    I have switched both and rebooted with the same results. I have flashed the BIOS to the current A12 version, same results. I cannot figure out what is causing the BIOS to pause for input rather than just (in old terms) running the autoexec file and booting the operating system. Normally the opposite is true; it is hard to remember the command to get the BIOS to pause and run the set up utility.
  • mspepper

    3 Posts

    1406

    0

    Posted December 16th, 2007 23:00

    Did you try to push F2 to go into Bios.  Leave Bios and save changes.  You've probably had a change (sometimes this happens with a memory upgrade) you push F2 go to the memory module, exit out and save changes.  Usually fixes the problem and will boot right up.
  • 1406

    0

    Posted December 17th, 2007 11:00

    Same. This problem has existed with this server since day one, with software auto-updates, it is annoying when they force a re-boot. I have been in and out of BIOS a dozen times in the last week working on this and changing the boot sequence. My BIOS is now level A12 (current version). The boot stops after the POST and forces you to pick F1 or F2. There are no errors in the POST and no reported changes in any devices, memory, or configuration. Is this just the way this server works?
  • 1406

    0

    Posted December 17th, 2007 18:00

    kgoodman54,
     
    Generally when we see the F1 F2 prompt, it will list on the screen what the problem is.  What does it say before the F1 F2? 
  • 1406

    0

    Posted December 18th, 2007 16:00

    The following is the complete text returned from the POST
     
    "Two 2000 MHz Processors, Bus Speed: 533 MHz, L2 Cache: 512 Kb
     
    Secondary hard disk drive 0 not found
    Secondary hard disk drive 1 not found
     
    LSI Logic Corp. MPT BIOS
    HBA    ID    LUN      Vendor        Product                     Rev            Sync    Wide   Capacity
      0        6       0         ARCHIVE    Python 06400-xxx     9100          80.0       16
      0        7       0         LSI Logic     1020/1030[   202]      1032300    320.0     16
     
    LSI Logic Corp MPT boot ROM
    No supported devices found!
     
    HA-0 (Bus 1 Dev 2) Perc 4/SC Standard FW3.28 DRAM=64Mb
     
    1 Logical drives found on the host adapter
    1 Logical drive(s) handled by BIOS
     
    Strike F1 to continue, or F2 to run setup utility."
     
     
    NOTE: Pressing F1 goes straight into Windows 2003 Server which runs fine. Pressing F2 goes to BIOS setup which when exited goes into Windows fine.
     
    Does this identify any errors?
  • 1406

    0

    Posted December 19th, 2007 12:00

    kgoodman54,
     
    You will need to go to the bios and turn off Secondary Drive 0 & 1.  This will stop the F1 F2 error from appearing.
  • 269

    0

    Posted December 20th, 2007 14:00

    Thanks to everyone that has contributed, and thank you Dennis - IT WORKS!