UNSOLVED

paenguin

updated

18 years ago

P

paenguin

6 Posts

0

30411

June 14th, 2008 00:00

MD3000 CLI not responding

Hi Guys,

 

I am trying to reset the password for MD3000 since the person who previously configured it left the company and didn't told me the password.

 

I connected the Password-Reset cable. Connected via HyperTerminal, configured COM port as 115200 8-N-1; but i do not get a response form the controller. only a blank terminal. i have checked that i am connected to the Controller 0 port. 

 

Also, I checked the cable if it is working on another MD3000 and confirmed that i am able to access the CLI.

 

Please help. Thanks!

 

Cheers!

Paeng 

  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    429

    0

    Posted June 16th, 2008 13:00

    Which step did you get to on the password reset document 

    <ADMIN NOTE: Broken link has been removed from this post by Dell>

    that's on the Dell site?

  • paenguin

    6 Posts

    429

    0

    Posted June 16th, 2008 18:00

    i got as far as connecting the PS2 connector to the controller 0 port, configure HyperTerminal to right packet size, and that's it...

     

    all i got was the blinking space.. :( 

  • dzenz

    175 Posts

    429

    0

    Posted June 16th, 2008 19:00

    Stating the obvious... HyperTerminal is not connecting.

     

    Are you are able to connect to another MD3000 using the same HyperTerminal session setup and cable?

     

    Have you tried controller 1 in the same array?

     

    Have you tried rebooting the array when the HyperTerminal session is active?

     

    Dave

  • 429

    0

    Posted June 16th, 2008 20:00

    Where you using the same computer to connect to the array when you tried on the other MD3000, the one that works?

     

    One more thing to try. Set up the correct baud rate on Hyperterm, before powering up the MD3000, then hook it up and power up.

     

    PA

     

    Message Edited by pablito.arias on 06-16-2008 04:41 PM
  • paenguin

    6 Posts

    429

    0

    Posted June 16th, 2008 20:00

    yes, yes and yes...

     

    i used the hyperterminal and cable on a different MD3000, works perfectly..

     

    On the problematic MD3000, both controllers DO NOT respond to the hyperterminal session. i also manually restarted the array while HyperTerminal is active, yet i still got nothing.

     

    i googled this problem hoping to find a solution after i exerted every knowledge i have on this,when i stumbled on this support forum and hope to get this fixed.

     

    cheers! 

  • paenguin

    6 Posts

    429

    0

    Posted June 16th, 2008 21:00

    yup. same computer, same session, same cable.

     

    hmmm.. ok il try to that one..

     

    if it still doesnt work, i guess i have to call in DELL support. 

  • paenguin

    6 Posts

    429

    0

    Posted June 17th, 2008 14:00

    yup.. i pressed Ctrl-B.. 

     

    is there any other way to do this? 

  • 429

    0

    Posted June 17th, 2008 14:00

    Did you try Ctlr-Pause(Break) ?
  • Dev Mgr

    6 Operator

    •

    9308 Posts

    •

    3 Points

    429

    0

    Posted June 17th, 2008 14:00

    The PDF says to press control-B. I assume this isn't showing anything then? The blinking cursor is where you start, but w/o pressing the control-B you won't get anything else.
  • paenguin

    6 Posts

    56

    0

    Posted June 20th, 2008 19:00

    thanks pablito.. that worked.

    cheers!