UNSOLVED

Phiwie

updated

14 years ago

P

Phiwie

3 Posts

0

5400

May 12th, 2013 10:00

V305

I inherited a hand-me-down DELL V305 printer.  THere is a new black cartridge but when it prints the page is blank and error message says to remove plastic.  So I think the previous owner didn't remove and I take out cartridge but can't seem to find what 'plastic' needs to be removed.  When I feel ink outlet it does seem to be covered but without moving the coppery thingy with coding I don't know what to do to get it uncovered :-(  HELP!!!

  • PudgyOne

    11 Legend

    •

    30315 Posts

    •

    106638 Points

    750

    0

    Posted May 12th, 2013 10:00

    Phiwie,

     

    Are you using Dell Series 9 ink cartridges?

     

    If you unplug the printer from the wall and remove the power brick for 60 seconds, this will reset any error messages the printer has. I would then plug everything back in.

     

    Power on the printer. 

     

    Open the printer(with the power on) and take out the Dell Series 9 black cartridge and then reseat it. I would then take out the color Dell Series 9 ink cartridge and reseat it. Now close the printer and it will print an alignment page.

     

    Any error messages?

     

    black cartridge = black side(left side)          color cartridge = color side(right side)

     

    photo cartridge = black side(left side)          color cartridge = color side(right side)

     

    Dell Series 9 ink cartridges have a sensor in them that cannot be reset. Article on refilling Dell ink cartridges.

     

    Dell Series 9 ink cartridges can be purchased at Staples, Walmart or Dell's Website.

     

    It's possible to get a Dell Series 9 ink cartridge with a bad sensor. I would take these back to the place of purchase for a replacement.

     

     

    Rick

  • Phiwie

    3 Posts

    750

    0

    Posted May 12th, 2013 10:00

    Yes re Series 9 - powered down and powered up, reseated cartridges, machine when through motion of printing but came out blank.  Error message says there is alignment problem. remove tape from cartridges.  When I touch bottom of coloured cartridge I can feel where ink comes out bottom but on black cartridge the ink outlet does appear to be covered with film but I can't seem to find away to remove without damaging sensor tape

  • PudgyOne

    11 Legend

    •

    30315 Posts

    •

    106638 Points

    750

    0

    Posted May 12th, 2013 11:00

    Phiwie,

     

    Sensor in both catridges, so both need some ink to print. You can tell it to use Black only, in printer preferences.

     

    Can you copy a document under the glass? Black & white and color? If not, the problem is the printer, either the Dell Series ink cartridge(s) or the printhead. I have see a few of the print heads go out, the original failed at an early time, but the replacement printhead has made mine last for years.

     

     

    Rick

  • Phiwie

    3 Posts

    750

    0

    Posted May 12th, 2013 11:00

    THanks Rick - I'd say I have a faulty cartridge which is basically why previous owner got rid of printer, couldn't get it to work so turfed it.  I'll go get a new cartridge.  I'm assuming I don't have to replace empty coloured cartridge?  I'm just needing b/w print.

  • PudgyOne

    11 Legend

    •

    30315 Posts

    •

    106638 Points

    750

    0

    Posted May 12th, 2013 11:00

    Phiwie,

     

    You can try...

    Cleaning Dell ink cartridges

     

    See if it helps. If the cartridges were new, I would take them back for a replacement.

     

     

    Rick