Unsolved
This post is more than 5 years old
138 Posts
0
1092
Kickstart didn't work
Hi,
I just kickstarted a brand new factory installed 4node centera.
I logged in via emcservice to node 4 thru eth 2 and issued FPkickstart -p 10.255
FPClusterNetLog showed following:
Sep 24 06:44:54 centera Clusternet: {info} Panel: [Net-Detect] [Listening...]
Sep 24 06:45:14 centera Clusternet: {info} Panel: [Net-detect] [2 switches found]
Sep 24 06:45:17 centera Clusternet: {info} Panel: [Net-detect] [SNMP eth1-1]
Sep 24 06:45:20 centera Clusternet: {info} Panel: [Net-info 90] [Temp-ip .212?]
Sep 24 06:45:20 centera Clusternet: {info} Panel: [Net-detect] [SNMP eth1-1]
Sep 24 06:45:23 centera Clusternet: {info} Panel: [Net-info 91] [Temp-ip .212]
Sep 24 06:45:23 centera Clusternet: {info} Panel: [Net-detect] [SNMP eth1-1]
Sep 24 06:45:24 centera Clusternet: {info} Panel: [Net-info 90] [Temp-ip .183?]
Sep 24 06:45:24 centera Clusternet: {info} Panel: [Net-detect] [SNMP eth1-1]
Sep 24 06:45:55 centera Clusternet: {info} Panel: [Initialize cube]
Sep 24 06:45:58 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:03 centera Clusternet: {info} Panel: [Net-info 90] [Temp-ip .52?]
Sep 24 06:46:03 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:06 centera Clusternet: {info} Panel: [Net-info 91] [Temp-ip .52]
Sep 24 06:46:06 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:24 centera Clusternet: {info} Panel: [Net-info 90] [Temp-ip .112?]
Sep 24 06:46:24 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:27 centera Clusternet: {info} Panel: [Net-info 91] [Temp-ip .112]
Sep 24 06:46:27 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:45 centera Clusternet: {info} Panel: [Net-info 90] [Temp-ip .156?]
Sep 24 06:46:45 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Sep 24 06:46:48 centera Clusternet: {info} Panel: [Net-info 91] [Temp-ip .156]
Sep 24 06:46:48 centera Clusternet: {info} Panel: [Net-info 92] [Finding cluster]
Than at this last line 06:46:48 it just stayed for more than an hour.
I tried logging in via CV to 10.255.1.4 but without success.
Any idea where I am at now?
GBcentera
46 Posts
0
October 30th, 2012 14:00
On each node type “ FPv” to see what the CentraStar version is – all nodes must be the same….
Next while you are on each node run FPclusternetlog to see what it is saying.
It may be the case where the nodes need to be reinitialized and brought up again.
?? Sep 24
Darmin_M
138 Posts
0
October 30th, 2012 22:00
I was able to login to all of the nodes using the emcservice password 4.2.x. I will login and issue the command.
Yes it is saying sep 24 which is also odd. I didn't think it was a big deal at a time because my next step was to set cluster time.
However, I didn't get a chance to do that.
Does the reinit require EMC eng or is it a procedure a on site engineer can do?
GBcentera
46 Posts
0
October 31st, 2012 10:00
In this state another step to try is to power cycle the system - all nodes and switches.
If not resolved then a person with the emcexpert credentials would be required locally to perform the corrective actions needed.