Hi and thanks for the post.

Just to clarify, are you saying that you had OME discovery working ok for ESXi5...but then you udpated to "update 1" and it does not work?

Thanks,

Rob

p.s.  also note the whitepaper on delltechcenter.com/ome for setting up ESXi...

Regarding the multi protocol discovery, OME does allow that. There is a priority order for protocols and usually SNMP is higher priority since it is commonly used across wide range of devices and it provides most amount of information for physical servers.

Regarding ESXi, WS-MAN protocol provides more information than SNMP. OME doesn't really get much information outside of WS-MAN for ESXi.

For ESXi 5.0 update 1, you will have to install OMSA 7.0 VIB available here:

www.dell.com/.../DriverFileFormats

Regards

Abhijit

No, we just use Update1 . We didn't try to discover ESX 5.0 without Update as we didn't have one.

thanks for p.s.

regards

I embraced that link & kissed both chicks :)

Thank you, Abhijit

Andrzej

You are welcome Andrzej. Let us know how it goes.

Cant get the OME to inventory my ESXi 5.0 U1 server. Just installed both OME and ESXi 5 so it has never worked.

I installed the "Dell_OpenManage_ESXi500_OM700-offline_bundle-643291.zip" and restarted.

Did a "esxcli software vib list" and it says "OpenManage 7.0-0000 Dell VMwareAccepted  2012-03-21"

Then I did a new discovery with only one ip-address in it and disabled all other tests then WS-man.

In WS-Man settings I put User ID: root

Password: same as the servers ssh use (Here is where im not sure if that is right)

Secure Mode: yes (Port changed to 443)

Skip Common name check: yes

Trusted Site: yes

But still only get "Unclassified" and not a ESX

Any advice?

The credentials and discovery settings look alright. Did you get the chance to look at the white paper below?

en.community.dell.com/.../20071085.aspx

You can also use the Dell Troubleshooting tool WS-MAN test to verify that the port and credentials are working for connecting to the target IP address.

There is version 3.0 of troubleshooting tool which ships with OME 1.0.1 release. You might be able to uninstall DTT 1.0 and install 3.0. It may help to debug this.

Done all that in the PDF file.

Still no luck.

And when I run the DTT WSMAN test I get this error:

Protocols Selected are:

WSMAN

Error An attempt was made to load a program with an incorrect format. (Exception from HRESULT: 0x8007000B)

But I get the same error when I try on any server that dont even got agent installed.

Tried a few of the test (Database, Name Resolution and SSH) and it works fine.

Im using version 1.0 of the Dell TroubleShoot Tool.

Tried to connect to a blade chassie with WSMAN but the same error.

Thanks for the update.

Are you getting this error from DTT for running WS-MAN test or any other test. Just want to check if DTT is running any test at all?

Thanks for the updates.

If you edit the existing discovery range the passwords have to be entered again for security reasons. If you don't edit the ranges, discovery will run on schedule and you will not have to re-enter passwords.

Oh, its working. Changed the timeout and retries in the test.

Got a few more ESXi to try on before I can say I made it! But that is for tomorrow to tell

Ah, yes. Found it.
Ok, so the test on the chassie was Ok and now even the test with ESXI is ok :-)

So on a ESXi with out the OM installed:

WSMAN profiles found on the remote device are:
1. Job Control
2. Software Update
3. PCI Device
4. Software Inventory
5. Indications
6. IPMI OEM Extension
7. Sensors
8. Software Inventory
9. Profile Registration
10. System Memory
11. Record Log
12. CPU
13. Fan
14. Base Server
15. Battery
16. Physical Asset
17. Power Supply
18. Power State Management

On a ESXi with OM installed:

WSMAN profiles found on the remote device are:
1. Job Control
2. Software Update
3. PCI Device
4. Software Inventory
5. Indications
6. IPMI OEM Extension
7. OpenManage
8. Sensors
9. Software Inventory
10. Profile Registration
11. System Memory
12. Record Log
13. CPU
14. Fan
15. Base Server
16. Battery
17. Physical Asset
18. Power Supply
19. Power State Managemen

So it is there but still dont it to work in OME
Still progress :-)

One question. When I edit the Discovery Range of the one I did the password is blank again. It feels like that may be the problem.

Thanks for the updates. Can you let us know if you changed the retries value as well. We will update this information in the FAQ section so that it will help others who run into this issue.