UNSOLVED
Node firmware 10.1.1 question (On OneFS 8.1.0.1)
Following a node firmware update to 10.1.1, the status of the firmware is:
Device Type Firmware Mismatch Lnns
-------------------------------------------------------------------------------------------------------
Mellanox-EN0 40GigE 2.40.5030+EMC1090111023 - 1-28
Mellanox-EN1 40GigE 2.40.5030+EMC1090111023 - 1-28
EPbmc_bblock_moons ePOST 01.40 - 1-28
EPbcc_infinity ePOST 00.69 - 1-28
EPps1 ePOST 02.02 - 1,3,5,7,9,11,13,15,17,19,21,23,25,27
EPssp_infinity ePOST 01.90 - 1-28
EPps0 ePOST 02.02 - 1,3,5,7,9,11,13,15,17,19,21,23,25,27
EPbios_warthog ePOST 28.14 - 1-28
EPspime_warthog ePOST 07.00 - 1-28
EPserdes_warthog ePOST 08.00 - 1-28
EPbmc_main ePOST 21.91 - 1-28
EPfp_fpioc ePOST 00.08 - 1-28
EPvrd0_warthog_stmicro ePOST 01.01 - 1-28
EPcmd_64pin ePOST 02.01.64.02 - 1-28
EPuefi_fw_volume_infinity ePOST 03.41 - 1-28
EPeth_infinity ePOST 02.52 - 1-28
EPsas_infinity ePOST 0001.0004.0000.11181 - 1-28
EPvrd2_warthog_stmicro ePOST 01.01 - 1-28
EPvrd1_warthog_stmicro ePOST 01.01 - 1-28
EPfp_fpinffw ePOST 02.0b - 1-28
EPfp_bootstrap ePOST 01.00 - 1-28
EPcdes ePOST 2.19.1+0.13.0+21.00 - 1-28
EPfp_fpfont ePOST 01.00 - 1-28
EPadpt_moons ePOST 01.50 - 1-28
EPpost_warthog ePOST 20.81 - 1-28
EPcmd_100d815pin ePOST 03.08.103.01 - 1-28
EPfp_bootloader ePOST 01.01 - 1-28
-------------------------------------------------------------------------------------------------------
From what i can make out, the status of EPps1 and EPps0 (Re: power supply I assume), is only on the odd numbered nodes.
When looking at the same from the WEBUI (cluster management > Patches and Firmware), It says that the same firmware is on all nodes (1-28).
Is the status of the the EPps1 and EPps0 firmware correct from the CLI?
Is this a problem with the Webui?
philippspohr
1 Rookie
•
107 Posts
1251
0
Posted December 1st, 2017 03:00
I suppose that are new Gen6 nodes?
With Gen6 Nodes the Nodes are grouped into pairs. Each node-pair shares a mirrored journal and two power supplies.
For the output of the firmware versions I would expect, that EPps0 is only available for all odd numbers (1,3,5,7,9,...) and EPps1 for all even numbers (2,4,6,8,10,...). Maybe there is a bug in 8.1.0.1 that the CLI is showing the wrong node numbers for EPps1.
On that point the WebUI is more correct because all Nodes are having the same newest firmware version. But there is the mistake, that the WebUI does not make a difference between the odd and the even numbers.
Apex_Ops
1 Rookie
•
90 Posts
1251
0
Posted December 1st, 2017 03:00
Yes, these are new Gen6 nodes.