Unsolved
This post is more than 5 years old
3 Posts
0
27264
November 22nd, 2013 16:00
PowerConnect 3548 - NO Connection to CLI
Hi,
i want to reset the 3548 to the factory defaults, because someone deleted the IP-configuration of the VLAN 1. So I can't connect to the switch by http. I connected via RS232 an Hyper-Terminal to the CLI. I see the output of the power-on self test but i can't send any command to the switch.
- Can I reach my goal without CLI?
- What can I do to reach the CLI?
Thank you for your help.
No Events found!
DELL-Josh Cr
Moderator
•
9.4K Posts
0
November 25th, 2013 07:00
It looks like it is reaching the console prompt and then sends the link is down errors. If you press enter or start typing commands does it bring up a console. Also earlier in the boot you may be able to enter the boot menu when this prompt is shown.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
From here you could choose the erase flash file which will make the switch nonbootable and then you can transfer a new firmware image.
DELL-Josh Cr
Moderator
•
9.4K Posts
0
November 25th, 2013 07:00
Hi,
The CLI or web GUI are the only methods. What is displayed on the screen after it shows the POST?
JCW03
3 Posts
0
November 25th, 2013 07:00
Hi Josh,
I connected the to the PowerConnect via RS232. After conneting the power-plug
Hyper-Terminal shows the following:
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 2.0.0.00 Built 03-Sep-2008 17:31:01
##
########### ##### ###### ######
############## ######### ###### ######
############### ######### ###### ######
################ ########## #### ###### ######
################ ######### ###### ###### ######
######################## ######### ###### ######
###### ############## ######## ####### ######
###### ###################### ######### ######
###### #################### ########## ######
###### ################### ########### ######
###### ################## ############# ######
###### ################################# ######
################################################# #
################ ################ ############# ############
################ ############## ############# ############
############### ########## ############# ############
############## ######## ############# ############
########### #### ############# ############
##
PowerConnect 3548 board based on Orion 88F5181 ARM926EJ processor
64 MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled.
MAC Address : 5c:26:0a:ca:fd:26.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-1
100%
OK
Running from RAM...
*********************************************************************
*** Running SW Ver. 2.0.0.40 Date 06-Dec-2009 Time 12:06:16 ***
*********************************************************************
HW version is 00.00.02
Base Mac address is: 5c:26:0a:ca:fd:26
Dram size is : 128M bytes
Dram first block size is : 102400K bytes
Dram first PTR is : 0x1800000
Dram second block size is : 4096K bytes
Dram second PTR is : 0x7C00000
Flash size is: 16M
01-Jan-2000 00:00:06 %CDB-I-LOADCONFIG: Loading running configuration.
01-Jan-2000 00:00:07 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
Slot 1 - PowerConnect 3548P
CPLD revision: 8.01
------------------------------------
-- Unit Standalone --
------------------------------------
Tapi Version: v1.3.3.1
Core Version: v1.3.3.1
01-Jan-2000 00:00:20 %INIT-I-InitCompleted: Initialization task is completed
01-Jan-2000 00:00:20 %Environment-I-FAN-STAT-CHNG: FAN# 1 status changed - opera
tional.
01-Jan-2000 00:00:20 %Environment-I-FAN-STAT-CHNG: FAN# 2 status changed - opera
tional.
01-Jan-2000 00:00:20 %Environment-I-FAN-STAT-CHNG: FAN# 3 status changed - opera
tional.
01-Jan-2000 00:00:20 %Environment-I-FAN-STAT-CHNG: FAN# 4 status changed - opera
tional.
01-Jan-2000 00:00:20 %Environment-I-FAN-STAT-CHNG: FAN# 5 status changed - opera
tional.
01-Jan-2000 00:00:20 %Environment-I-PS-STAT-CHNG: PS# 1 status changed - operati
onal.
01-Jan-2000 00:00:20 %Environment-W-PS-STAT-CHNG: PS# 2 status changed - not pre
sent.
01-Jan-2000 00:00:20 %Entity-I-SEND-ENT-CONF-CHANGE-TRAP: entity configuration c
hange trap.
01-Jan-2000 00:00:20 %SNMP-I-CDBITEMSNUM: Number of running configuration items
loaded: 19
01-Jan-2000 00:00:20 %SNMP-I-CDBITEMSNUM: Number of startup configuration items
loaded: 19
console> 01-Jan-2000 00:00:24 %LINK-W-Down: e1
01-Jan-2000 00:00:25 %LINK-W-Down: e2
01-Jan-2000 00:00:25 %LINK-W-Down: e3
01-Jan-2000 00:00:25 %LINK-W-Down: e4
01-Jan-2000 00:00:25 %LINK-W-Down: e5
01-Jan-2000 00:00:25 %LINK-W-Down: e6
01-Jan-2000 00:00:25 %LINK-W-Down: e7
01-Jan-2000 00:00:25 %LINK-W-Down: e8
01-Jan-2000 00:00:25 %LINK-W-Down: e9
01-Jan-2000 00:00:25 %LINK-W-Down: e10
01-Jan-2000 00:00:25 %LINK-W-Down: e11
01-Jan-2000 00:00:25 %LINK-W-Down: e12
01-Jan-2000 00:00:25 %LINK-W-Down: e13
01-Jan-2000 00:00:25 %LINK-W-Down: e14
01-Jan-2000 00:00:25 %LINK-W-Down: e15
01-Jan-2000 00:00:25 %LINK-W-Down: e16
01-Jan-2000 00:00:25 %LINK-W-Down: e17
01-Jan-2000 00:00:25 %LINK-W-Down: e18
01-Jan-2000 00:00:25 %LINK-W-Down: e19
01-Jan-2000 00:00:25 %LINK-W-Down: e20
01-Jan-2000 00:00:25 %LINK-W-Down: e21
01-Jan-2000 00:00:25 %LINK-W-Down: e22
01-Jan-2000 00:00:25 %LINK-W-Down: e23
01-Jan-2000 00:00:25 %LINK-W-Down: e24
01-Jan-2000 00:00:25 %LINK-W-Down: e25
01-Jan-2000 00:00:25 %LINK-W-Down: e26
01-Jan-2000 00:00:25 %LINK-W-Down: e2
01-Jan-2000 00:00:25 %LINK-W-Down: e28
01-Jan-2000 00:00:25 %LINK-W-Down: e29
01-Jan-2000 00:00:25 %LINK-W-Down: e30
01-Jan-2000 00:00:25 %LINK-W-Down: e31
01-Jan-2000 00:00:25 %LINK-W-Down: e32
01-Jan-2000 00:00:25 %LINK-W-Down: e33
01-Jan-2000 00:00:25 %LINK-W-Down: e34
01-Jan-2000 00:00:25 %LINK-W-Down: e35
01-Jan-2000 00:00:25 %LINK-W-Down: e36
01-Jan-2000 00:00:25 %LINK-W-Down: e37
01-Jan-2000 00:00:25 %LINK-W-Down: e38
01-Jan-2000 00:00:25 %LINK-W-Down: e39
01-Jan-2000 00:00:25 %LINK-W-Down: e4
01-Jan-2000 00:00:25 %LINK-W-Down: e41
01-Jan-2000 00:00:25 %LINK-W-Down: e42
01-Jan-2000 00:00:25 %LINK-W-Down: e43
01-Jan-2000 00:00:25 %LINK-W-Down: e44
01-Jan-2000 00:00:25 %LINK-W-Down: e45
01-Jan-2000 00:00:25 %LINK-W-Down: e46
01-Jan-2000 00:00:25 %LINK-W-Down: e47
01-Jan-2000 00:00:25 %LINK-W-Down: e48
01-Jan-2000 00:00:25 %LINK-W-Down: g1
01-Jan-2000 00:00:25 %LINK-W-Down: g2
01-Jan-2000 00:00:25 %LINK-W-Down: g3
01-Jan-2000 00:00:25 %LINK-W-Down: g4
PoE software version:
H.W. Version 0: Identifies the PCB version.
Full S.W. version is: Prod#.SW Ver.Param# - 0.603.4
Build Num 2, Internal SW 355.
PoE device version:
PoE Device 0, hw Version: 2. 12 ports.
PoE Device 1, hw Version: 2. 12 ports.
PoE Device 2, hw Version: 2. 12 ports.
PoE Device 3, hw Version: 2. 12 ports.
01-Jan-2000 00:02:30 %INIT-I-Startup: Cold Startup
After that nothing happens and there is no way to send commands.
JCW03
3 Posts
0
November 27th, 2013 02:00
Hi Josh,
thanks for your quick reply.
After the message - Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom. -
there is no possibility to interrupt. The system does not react after pressing ESC or RETURN or anything else.
It seems that the connection only recieve informations.
Abu umar
1 Message
0
May 29th, 2018 11:00
In my own case, when i connect through console i cant see anything
pls help me