Reset AP105 to factory settings

Hi ITMichelle,
You should be able to reset with the following commands
• Power on the AP and get into apboot mode.
• From the apboot prompt, configure:
apboot> purge
apboot> save
apboot> reset

SO on the 2nd IAP I ran the same sequence of purge, save, reset.  Seemed to work, but it is not finding our wireless instant controller....?  Is starting watchdog process part of the arbua default?

APBoot 1.0.9.12 (build 22797)

Built: 2009-11-04 at 15:53:54

Model: AP-10x

CPU:   AR7161 revision: A2

Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz

DRAM:  128 MB

POST1: passed

Copy:  done

Flash: 16 MB

PCI:   scanning bus 0 ...

      dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3

      00  00  168c  0029 00002   01 10000000 00000000 00000000 00000000

      01  00  168c  0029 00002   01 10010000 00000000 00000000 00000000

Net:   eth0

Radio: ar922x#0, ar922x#1

Hit to stop autoboot:  0

apboot> purge

Un-Protected 1 sectors

.done

Erased 1 sectors

Writing

apboot> save

Saving Environment to Flash...

Un-Protected 1 sectors

.done

Erased 1 sectors

Writing

apboot> reset

APBoot 1.0.9.12 (build 22797)

Built: 2009-11-04 at 15:53:54

Model: AP-10x

CPU:   AR7161 revision: A2

Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz

DRAM:  128 MB

POST1: passed

Copy:  done

Flash: 16 MB

PCI:   scanning bus 0 ...

      dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3

      00  00  168c  0029 00002   01 10000000 00000000 00000000 00000000

      01  00  168c  0029 00002   01 10010000 00000000 00000000 00000000

Net:   eth0

Radio: ar922x#0, ar922x#1

Hit to stop autoboot:  0

Checking image @ 0xbf100000

Image is signed; verifying checksum... passed

Signer Cert OK

Policy Cert OK

RSA signature verified.

ELF file is 32 bit

Loading .text @ 0x80e00000 (3788904 bytes)

Loading .data @ 0x8119d070 (32 bytes)

Clearing .bss @ 0x8119d090 (16 bytes)

## Starting application at 0x80e00000 ...

Uncompressing...................................

▒

Aruba Networks

ArubaOS Version 6.1.3.11 (build 41171 / label #41171)

Built by p4build@cartman on 2013-12-05 at 22:08:39 PST (gcc version 4.3.3)

CPU Rev: aa

71x CPU

Flash variant: default

Cache parity protection disabled

Using 340.000 MHz high precision timer. cycles_per_jiffy=680000

Memory: 122880k/131072k available (1850k kernel code, 8116k reserved, 693k data, 2968k init, 0k highmem)

available.

detected lzma initramfs

initramfs: LZMA lc=3,lp=0,pb=2,dictSize=8388608,origSize=12514304

LZMA initramfs by Ming-Ching Tiew ...............................................................................................................................................................................................

AR7100 GPIOC major 0

wdt: registered with refresh

Enabling Watchdog

Talisker RSSI LED initialization

Creating 1 MTD partitions on "ar7100-nor0":

0x00000000-0x01000000 : "flash"

i2c /dev entries driver

i2c-talisker: using default base 0x18040000

AD7416 driver probing for devices on AR7100 I2C

.<6>lo: Disabled Privacy Extensions

IPv6 over IPv4 tunneling driver

Starting Kernel SHA1 KAT ...Completed Kernel SHA1 KAT

Starting Kernel HMAC-SHA1 KAT ...Completed Kernel HMAC-SHA1 KAT

Starting Kernel DES KAT ...Completed Kernel DES KAT

Starting Kernel AES KAT ...Completed Kernel AES KAT

Domain Name: arubanetworks.com

No panic info available

Testing TPM... Passed

ag7100_mod: module license 'unspecified' taints kernel.

AG7100: Length per segment 512

AG7100: Max segments per packet 4

AG7100: Max tx descriptor count    400

AG7100: Max rx descriptor count    252

AG7100: fifo cfg 3 018001ff

AG7100CHH: Mac address for unit 0

AG7100CHH: 00:24:6c:c0:24:60

ATHRF1: Port 0, Neg Success

ATHRF1: unit 0 phy addr 0 ATHRF1: reg0 0

AP xml model 39, num_radios 2 (jiffies 4145)

init_asap_mod: installation:0

radio 0: band 1 ant 0 max_ssid 8

radio 1: band 0 ant 0 max_ssid 8

setting bond0 as bridge child

setting gre0 as split child

Starting watchdog process...

Getting an IP address...

ag7100_ring_alloc Allocated 4800 at 0x813d4000

ag7100_ring_alloc Allocated 3024 at 0x813c6000

AG7100: cfg1 0xf cfg2 0x7014

ATHRF1: Port 0, Neg Success

ATHRF1: unit 0 phy addr 0 ATHRF1: reg0 3100

AG7100: unit 0: phy not up carrier 1

Writing 4

ADDRCONF(NETDEV_UP): bond0: link is not ready

AG7100: unit 0 phy is up...RGMii 1000Mbps full duplex

AG7100: pll reg 0x18050010: 0x110000  AG7100: cfg_1: 0x1ff0000

AG7100: cfg_2: 0x3ff

AG7100: cfg_3: 0x18001ff

AG7100: cfg_4: 0xffff

AG7100: cfg_5: 0xfffef

AG7100: done cfg2 0x7215 ifctl 0x0 miictrl 0x22

ADDRCONF(NETDEV_CHANGE): bond0: link becomes ready

10.0.xxx.xxx 255.255.255.0 10.0.0.1

Running ADP...cat: /tmp/master: No such file or directory

Done. Master is

killall: nanny: no process killed

killall: sapd: no process killed

Sending SIGKILL to all processes.

Please stand by while rebooting the system.

Restarting system.

.

The watchdog process should be on both. If it is stopping there try changing the ip address of the controller to the one that you are using.

Thanks Josh.

I tried that sequence of commands on the one that tells me it's a bad image.   No change, still a bad image.  See below (changed a couple identifiers).   It gets through DHCP and receives an IP.  It looks like it's looking for Aruba Master - but I am not sure ours is named "arbua master".   any ideas?

Hit to stop autoboot:  0

apboot> purge

Un-Protected 1 sectors

.done

Erased 1 sectors

Writing

apboot> save

Saving Environment to Flash...

Un-Protected 1 sectors

.done

Erased 1 sectors

Writing

apboot> reset

APBoot 1.2.4.4 (build 26618)

Built: 2011-01-07 at 13:42:04

Model: AP-10x

CPU:   AR7161 revision: A2

Clock: 680 MHz, DDR clock: 340 MHz, Bus clock: 170 MHz

DRAM:  128 MB

POST1: passed

Copy:  done

Flash: 16 MB

PCI:   scanning bus 0 ...

      dev fn venID devID class  rev    MBAR0    MBAR1    MBAR2    MBAR3

      00  00  168c  0029 00002   01 10000000 00000000 00000000 00000000

      01  00  168c  0029 00002   01 10010000 00000000 00000000 00000000

Net:   eth0

Radio: ar922x#0, ar922x#1

Hit to stop autoboot:  0

Checking image @ 0xbf100000

Invalid image format version: 0xffffffff

Checking image @ 0xbf800000

Invalid image format version: 0xffffffff

eth0 up: 1 Gb/s full duplex

DHCP broadcast 1

DHCP IP address: 10.0.x.xxx

DHCP subnet mask: 255.255.255.0

DHCP def gateway: 10.0.0.1

DHCP DNS server: 10.0.0.250

DHCP DNS domain: domain.org

ADP multicast 1

ADP broadcast 1

ADP multicast 2

ADP broadcast 2

checksum bad

ADP multicast 3

Retry count exceeded

DNS request 1 for aruba-master.domain.org to 10.0.0.250

T T T T

Retry count exceeded; starting again

eth0 up: 1 Gb/s full duplex

Try reflashing the firmware and see if it fixes the image. It sounds like the factory reset put it back to the way Aruba sent it to us and not the way we ship them.