Unsolved
1 Rookie
•
3 Posts
0
16
VRTX R1-2210 failed to boot
Tapi Version: v1.9.6
Core Version: v1.9.6
01-Oct-2006 05:24:30 %HAL_hw_lion-F-SetInfModeAndSpeedFailed: Failed to configure ifIndex 5 speed 2 interface mode 3 status 1
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 2.0.0.67 (date 18-Dec-2016 time 11:28:21)
Found an old thread that said pulling battery worked for them, no luck for me. Any ideas? I can access it with USB console cable, but Tera Term XMODEM transfer seems not to work.
Core Version: v1.9.6
01-Oct-2006 05:24:30 %HAL_hw_lion-F-SetInfModeAndSpeedFailed: Failed to configure ifIndex 5 speed 2 interface mode 3 status 1
***** FATAL ERROR *****
Reporting Task: ROOT.
Software Version: 2.0.0.67 (date 18-Dec-2016 time 11:28:21)
Found an old thread that said pulling battery worked for them, no luck for me. Any ideas? I can access it with USB console cable, but Tera Term XMODEM transfer seems not to work.
INP-User
1 Rookie
1 Rookie
•
3 Posts
0
May 21st, 2024 23:45
Booting from SPI flash
High speed PHY - Version: 2.1.2 (COM-PHY-V20)
Update PEX Device ID 0x67100
High speed PHY - Ended Successfully
DDR3 Training Sequence - Ver 5.2.0
DDR3 Training Sequence - DEBUG - 1
DDR3 Training Sequence - Run without PBS.
DDR3 Training Sequence - DEBUG - 2
DDR3 Training Sequence - DEBUG - 5
DDR3 Training Sequence - DEBUG - 6
DDR3 Training Sequence - DEBUG - 7
DDR3 Training Sequence - DEBUG - 8
DDR3 Training Sequence - DEBUG - 11
DDR3 Training Sequence - DEBUG - 12
DDR3 Training Sequence - Ended Successfully
Status = MV_OK
BootROM: In-flash image checksum verification PASSED
Boot1 Checksum Test...............................PASS
Boot2 Checksum Test...............................PASS
Flash Image Validation Test.......................PASS
BOOT Software Version 2.0.0.1 Built 27-Jan-2014 12:07:49
Networking device with Marvell ARMADA-370 SoC 1.2GHz. 512 MByte SDRAM.
I-Cache 32 KB. D-Cache 32 KB. L2 Cache 256 KB. Cache Enabled.
MAC Address : 14:18:77:ed:f4:f3.
Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom.
Preparing to decompress...
100%
Decompressing SW from image-2
100%
OK
Running from RAM...
*********************************************************************
*** Running SW Ver. 2.0.0.67 Date 18-Dec-2016 Time 11:28:21 ***
*********************************************************************
HW version is 00.00.01
Base Mac address is: 14:18:77:ed:f4:f3
Dram size is : 512M bytes
Dram first block size is : 471040K bytes
Dram first PTR is : 0x3000000
Dram second block size is : 4096K bytes
Dram second PTR is : 0x1FC00000
Flash size is: 32M
.......................................................................................................................................................................................................................................................................................................................................................................................01-Oct-2006 05:24:25 %CDB-I-LOADCONFIG: Loading running configuration.
01-Oct-2006 05:24:25 %CDB-I-LOADCONFIG: Loading startup configuration.
Device configuration:
Slot 1 - R1-2210
------------------------------------
-- Unit Standalone --
------------------------------------
DELL-Erman O
Moderator
Moderator
•
2.3K Posts
0
May 22nd, 2024 07:43
Hello,
Okay that's not easy one. A faulty battery can cause configuration loss during boot. You may try to battery reset
battery reset:
But if this doesn't help, I suggest you contact your local support team and open a ticket. Because a detailed examination may be required.
Hope that helps!
INP-User
1 Rookie
1 Rookie
•
3 Posts
0
June 5th, 2024 16:32
Put new battery in, same result.