Search

Is there a way to prevent the VLTi from managing certain VLAN traffic in OS9? This question expands on the discussion here. Essentially, we will have a couple VLANs designated for iSCSI traffic and we do not want that traffic traversing the VLTi. Based on the discussion mentioned above . . . I'm no

OS10 defaults to "Spanning tree enabled protocol rapid-pvst with force-version rstp". Does this mean that when it interacts with Cisco switches it uses Rapid-PVST+ but when it interacts with other manufacturer switches, it just uses RSTP? Thanks.

In OS10, a mechanism for this already exists: vlt delay-restore orphan-port enable. It allows you to define orphan ports and uses the delay-restore timer to delay the bring up of those ports. In OS9, there is only port-delay-restore which delays the bring up of all ports after a switch reboot. A pe

Please could you confirm the EOS and EOL for the Dell S4128F-ON and S4128T-ON switches. i.e. When will Dell stop extending support for these devices?

On power-up: (& continue) Is there a way to recover from that?

We've been attempting to reach a pair of S4048-ON switches via SSH over the network. We have configured IP addresses for the OOB management ports on each switch and attached it to our network via a small "dumb" switch but have had no luck establishing a connection. We can, however, establish a SSH s

Hello, When trying to read a file containing a valid rsa key, FTOS claims it's invalid: f10a(conf)#ip ssh pub-key-file sshkey.pub% Error: No valid host key(s) found OS version is 9.14(1.14)Any tip would be truly appreciated. Kind regards.

This command exists in the User’s Configuration Guide Version 6.7.0 page 1184 show ip dhcp global configurationVerify the global DHCP server configuration The following is from a console run: Machine Description............... Dell EMC Networking SwitchSystem Model ID................... N202

Hej, I've got a couple of S4128s, and today one was shutdown during a power outage. After the power came back, the device was not working properly. System led was blinking slowly.  No interfaces came up.  Attached a serial cable, saw the switch name and login prompt, and drew a sigh of

Hi All.I have a dell switch S4148T. In the configuration are defined multiple vlans.The switch has trunk port for all vlans to connect vmware esxi node.Routing mode is enabled. Example vlan and routing SW# show ip routeCodes: C - connected      S - static       B

Hello, I am looking for how long the above switch will receive security updates, thank you

I have been though the upgrade notes on these switches and I have some questions. Since these are in essence "new" switches to me, I am starting from a hard reset and both switches need a firmware update. There are two versions of firmware update; the older is recommended and the newer is option

The documentation says this device supports a maximum of 256 leases. There are two kinds of DHCP IP assignments as far as I understand pool assigments where devices get 'random' addresses from a pool and manual assignments where a MAC address is mapped to an IP address.  The 256 leases support

I am having some trouble finding information on this. I originally came across this doc stating that "If a new USB flash drive is installed without un-mounting the previous drive, the new flash drive may not be recognized". I found no unmount command in OS9 on my S4048. I later realized that doc was

We will have two S4048-ON switches in VLT with a port-channel towards an "access" switch that doesn't support port dampening. Until we replace this switch, we were wondering if there is any reason that manually shutting down it's connected interface(s) would not be a sufficient workaround during mai

I'm using a DELL switch, but I'm confused about product maintenance terminology. If you click the link below, you will see information about “Product Life Cycle (End of Support and End of Life) Policy for Dell Data Security” https://www.dell.com/support/kbdoc/en-us/000128563/end-of-life-end-of-sup

I want to leak routes matching a specific /16 from the default vrf to a voice vrf. We have S5248F-ON switches running 10.5.4. I put this into the config: ip prefix-list voice-export seq 10 permit 10.10.0.0/16 route-map voice-export permit 10 match ip address voice-export ip vrf default  updat

Hello All, I have configured two VLT connections to two firewalls running active/standby. I like to know if I can use the priority statement in the VLT configuration on the same switch to prefer the traffic to go to the active firewall and when the active firewall fails, I will switch the traffic t

Hello All, I like to know if a VLT configuration on Dell Switches, Z9100-ON, will work connecting to a Juniper Firewall configured as active/standby. I am not familiar with Dell VLT but my understanding of Cisco VPC is that both units are active/active and my concern is the Dell VLT will send traff

Hi there, I'm planning to implement the following architecture, where a server establishes i/eBGP sessions with both VLT pairs. As it can be seeing in the following diagram/link, Cisco supports it. However, I could NOT find any Dell documentation mentioning support for this architecture. Is this a