Search Results (1.6K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
I've gone through and attempted to setup RADIUS, but when i plug in a device, the switch never reaches out to my NPS server. Any help would be great. !System Software Version 6.7.1.17 ip address 192.168.19.8 255.255.255.0exitip default-gateway 192.168.19.1username "admin" password privilege 15 en
Question
•
Networking General
Community Accepted Solution
Hi Team, I present a problema with PCIe Slots. It was working OK.. But now it is not recognizing Any Card. I Try with others PCIe of Fiber that working fine in others servers nodes but not have response. I use the pcie Fiber in other server.. And working fine.. So the Slot is not working..
Question
•
Networking General
Community Accepted Solution
Hello, Our core switch is an S4048-ON with v9.10(0.1) and we'd like to update to latest firmware. When searching the product page there are several versions available. Two OS and one firmware? I assume v9.14.2.17 is the one we want, but what is "Firmware Updater?" Thanks in advance
Question
•
Networking General
Community Accepted Solution
Hello , i would like to stack switch's model as follow S4048-ON with S6010-ON my questions is : Is it possible ? If yes how can i control te port # to be stacked ,for example on my S4048-ON i would like to use Forty 51,53 and on S6010-ON ports 29,31 if its its not possible , i intend to re
Question
•
Networking General
Community Accepted Solution
Hello all, I have been diagnosing a power connect 6248 for the past couple weeks now where many devices connected to said switch intermittently drop packets. Some devices work without drops but others flip flop between dropping and not. I am fairly certain the issue is with the switch since using a
Question
•
Networking General
Community Accepted Solution
Hi We have 2 Dell N1548P Firmware 6.6.0.13 running. Switch does what he is supposed to do but no Connection via ssh, https or Console is possible. (Telenet and plain-http disabled) I conected the console port to the second Unit of the Stack an trying to connect to Master Unit geting the f
Question
•
Networking General
Community Accepted Solution
I have ports 7 and 9 on same configuration. port 7 is h264 NVR for security camaras on with IP 192.168.0.30 port 9 is a laptop with IP 192.168.0.6 same subnet Ping from laptop to NVR fails. If I use my old 16 port switch , both on vlan 2, 192.168.0.30 replies to the ping.
Question
•
Networking General
Community Accepted Solution
Hello, This may have been asked before by others, but I've been unable to find a clear answer. If we don't use hiveagent and current status is (copied below) disabled/rejected, do we still need to go through the commands to stop app/delete the files? Thanks in advance! #show hiveagent statu
Question
•
Networking General
Community Accepted Solution
Is there ever a scenario where you might want to add more than one domain when you only have a single pair of switches? In the documentation, you only ever see one domain configured. I am curious. Currently I have a pair of S5148f running OS10 Thanks Hatter
Question
•
Networking General
Community Accepted Solution
How do I check the current configuration and how do I disable TLS 1.0 and 1.1 on the switch above? Newbie here, would appreciate a feedback.
Question
•
Networking General
Community Accepted Solution
Hi, I have a DELL S5248F-ON switch running OS 10.5.2.3. I'm familiar with Cisco Nexus switches that offer a 'port-profile' feature which allows the admin to define configuration centrally on the switch under the profile and then on the switch port put the name of the port profile with no config. Th
Question
•
Networking General
Community Accepted Solution
I have read the documentation fairly thoroughly, and I have scoured the net, but I cant seem to find a simple answer to my question(s). Assuming the 3 scenario's I have as examples below use the same two switches with a VLTi link, what would be the difference in functionality between these
Question
•
Networking General
Community Accepted Solution
Trying to configure sflow on a N2048 with firmware 6.7.17. If I paste in all my sflow commands, all take and if you use show commands to verify sflow all looks good. But after about a minute, all the sflow commands then disappear and the show commands show sflow isn't configured. What is goin
Question
•
Networking General
Community Accepted Solution
Greetings, I have a strange problem with a 1548 switch. At first glance it appears to be working, lights flashing, console access, ping response. But it doesn't allow internet access. Then, when I took out some cables, the lights keep on, as if still connected. And when I turned it off and on again
Question
•
Networking General
Community Accepted Solution
I don't know if someone could help on this but today after I powered up my n3024 switch it did light up all its LEDs but then stayed the same and the switch won't function. It looks like not getting through startup just lit up like an Xmas tree. Removed both PSU, card and cabling and res
Question
•
Networking General
Community Accepted Solution
I have two S4148F-ON connected with a VLT domain. i do not have the admin (or any) password to log into these. i can schedule downtime to do the password recovery. does anyone have a pointer to a current guide for doing this?
Question
•
Networking General
Community Accepted Solution
Hi, i want to update the switch i found two firmware options. Which should I use? (1) Dell EMC Networking N1100-ON Series Firmware version 6.7.1.17 (2) Dell Networking N1100-ON Series, Firmware Version 6.8.0.1 Support for PowerSwitch N1100-ON Series | Drivers & Downloads | Dell Anguilla &
Question
•
Networking General
Community Accepted Solution
Hello Quick question. I'm investigating the use of ansible with DELL switches N15xx series. I found some documentation online where it is asking you to find the OS version of the switch. Is the OS version the same as the firmware version? My firmware version is 6.7.x.x. Does that mean my OS is 6?
Question
•
Networking General
Community Accepted Solution
Hi , I have old witch model Dell N2048.connected with console to switch and then I did :Display boot menu > Restore configuration to factory defaultit was ok but after that i did by mistake : reformat partition or something like that and then now i stuck on U-Boot.When I connect to the switch with a
Question
•
Networking General
Community Accepted Solution
I want to be able to disable/enable ports via terminal.(on eg N1548 switches). I found this for disabling portshttps://www.dell.com/community/Networking-General/Disabling-Interface-ports/td-p/4162842 Works fine:) But i cant see any command there that would enable the port again:)There is no corres
Question
•
Networking General