Search

Hello, I am hoping someone can please help me. I am trying to setup a DMZ network. My setup is as follows, 2 x clustered fortigate 300e firewalls 2 x stacked Dell core switches S4048-ON in Layer 2 mode 2 x VMWare 6.7 ESXi hosts I have created the DMZ zone on the fortigates and set the IP to 192.

Hi, Do these switches support dhcp options? i need to migrate switches from Cisco to Dell and i need to configure this: option 2 hex b9b0option 42 ip 10.16.5.10 option 120 hex 0006.6469.616c.696e.0774.656d.656e.6f73.0363.6f6d.00 thanks

Can someone take a look at the attached management switch quote? I need to break out the maintenance and hardware numbers for this quote but I only see one line item. I also notice it is listed as a kit. Does this one line item include maintenance, cables, hardware and all licensing for this swit

Hi all,   in the N3200 speecsheet*, vxlan support is described as the following:  "VXLAN support in hardware only ². ² Can be used if enabled by ON partner network operating system"   What does it mean ("in hardware only")? Is a partner-device with vxlan support according to&nb

Hello, We have to make ACLs on S3148 (two S3148 as failover). But to make sure it is ok, i would like to send traffic logs to my rsyslog server. My rsyslog is configured with TLS and certificate (it works with fortigate units). Is it possible to send only traffic log to rsyslog with StartTLS and

I cannot find any information about QinQ support for Dell OS 10. Is there any way for OS10 to understand QinQ or is it simply not supported? If it is not supported, does anyone know whether it is on the roadmap?

Hi, I bought the N1548p switch and I need monitoring the CPU usage on zabbix. But, I cant found the OID for that. Im using the latest firmware. I tried with OID from earlier versions, searching in mib browser and the mib folder downloading the drivers of latest firmware version.   Could

I don't have a serial cable for Dell EMC CT-SCv2020, I am trying to SSH into it using the management IP but getting "Connection refused".  In another discussion, it was mentioned  Before trying to utilize SSH, you must create your RSA/DSA key pairs (private and public keys used for asymm

Hi, I have two N3048P switches in a stack running version 6.5.4.18 and I am trying to get ssh configured. Telnet is enabled so I can access it remotely currently, but would like to use ssh. What I did: 1. Enter into configuration mode: (conf t) 2. no ip ssh server 3. crypto key zeroize dsa 4. c

Hi, Where can we find the known issues list of DNOS 6.7.1.9?    Thanks in advance!    Lex

Hello, We have a N4032F Stack configured with RSTP. It has two uplink switches, VLAN 20 and 21 uplink to a Unifi switch and VLAN 200-210 uplink to a cisco switch. The stack is using RSTP and it elected the unifi switch as the root bridge since it has an STP priority of 4092 while the cisco switch h

I recently obtained a FORCE10 S50-01-GE-48T-AC, and when I connect my cable to the console port, and try connecting with the default settings, I get no output in the console window. I am using putty, and a Cisco to USB cable, connected through a crossover ethernet jumper. I have also tried the cisco

HelloI checked the log below on the switch. %STKUNIT1-M:CP %CHMGR-4-TEMP_STATUS_CHANGE: Unit 1 temperature state changed to 1 (Current temperature 40C).%STKUNIT1-M:CP %CHMGR-4-TEMP_STATUS_CHANGE: Unit 1 temperature state changed to 2 (Current temperature 45C). I know the switch temperature is 40C,

Hi All, I'm facing an issue where my radius server is sending a CoA packet to my Dell N2048P switch, but my radius server responds with 'No response from network device'. Once I debug the switch with command 'debug aaa coa' I get the following logs when sending a CoA:   ../../../../src/ap

Hello,   I have S4128F-ON, and this switch should be connected to a Cisco switch with 1G copper cables,   can I use Transceiver, 1000Base-T, to do this connectivity?    S4100: saying this support  multifunction,1/10/25/40/50/100 GbE top-of-rack (ToR)  http

Hi Dell Team, I need your help please. I am stuck in my configuration. We have 2 Dell layer 3 switches (acting as router for our network), There are 3 VRRP configurations there and working fine, one master and one back up.   Last week for testing I had configured the VRR

Greetings Everybody! I am asking cause i can't seem to find any guide about configuring static VXLAN using OS 10. I am using 10.5.0.0 version (GNS3) but i am missing lots of info it seems.I don't want any EVPN with BGP setup... Its overly complex for my level and needs at the moment.... So is there

I have two n1148-on that I've been struggling to get to work with uplinks and other switches. After I factory reset them, I don't get the blue ports on the GUI. Two out of four are greyed out on one and the other all 4 are greyed out and cant get them to take a link.  

I'm trying not to be confused. LOL As I understand it, there is no "Default Gateway" on the S4048. So to get the same result, assuming my firewall is 192.168.3.2, is it as simple as: #ip route 0.0.0.0/0 192.168.3.2 255 The "255" would be the preference so it would try all the internal routes befo

Hi. I could not found the command for NAT in docs. Does Dell S5248F-ON support NAT capabilities? Thanks.