Search Results (910)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
We've faced the issue while we extend HDD by insert full 24 slots. - Previously 12 HDD are 300GB of capacity - Insert new 12 HDD Capacity size 600GB We have 2 spare HDD 300GB and 600GB but spare 300GB alert : Disk too small. How to fix this issue while customer don't see the alert ?
Question
•
EqualLogic
Community Accepted Solution
I upgraded a server from 2008 to 2012 R2. I believe this server had the first installation of SAN Headquarters installed. I also have the SAN Headquarters app on my local PC desktop. The app failed on to run on the server so I re-installed it - it prompted for the log directory - I could not locate
Question
•
EqualLogic
Community Accepted Solution
Hello, I need some advice about an issue. This is time issue with Equallogic FS7610(v4.0.400005)/PS6210(v9.1.4).In the monitoring panel i have messages about NAS 0 & 1 controller time is not synchronized with Active directory (delay is more than 270 sec ). NTP servers (same as Active directory)
Question
•
EqualLogic
Community Accepted Solution
Hi, I am new to these Devices, in my environment we have 2 Dell EquilLogic devices and we got Failed drives on both devices. These are out of support i believe Slot Type Model Size RPM Status Errors SMART Health---- -------- ---------------- ----------- ----- --------- ------ ------------ 1 SAS(
Question
•
EqualLogic
Community Accepted Solution
Hello, I am having an issue configuring a new iSCSI connection on a new Win2016 server. Standard procedure is to install Auto Snapshot Manager and then configure the VSS Chap and grab the servers Initiator Name and add it to the new volume on the SAN, limiting access to only that Initiator. We then
Question
•
EqualLogic
Community Accepted Solution
Hello, I recently moved my SAN to a new IP address. I thought I changed all the IP addresses I needed to in the SAN configuration. The SAN is working fine. However, I am still getting automatic emails saying my SAN group is not responding to ping requests, because whatever program is p
Question
•
EqualLogic
Community Accepted Solution
I rebooted a Windows 2012 server that had an iSCSI connection to an Equallogic 6100 SAN. Following the reboot I checked File Explorer and the X: drive was not present. I launched the iSCSI initiator app and the target displays as connected. I disconnect and connected. I checked Disk Manager - ran a
Question
•
EqualLogic
Community Accepted Solution
Hi everybody! I have the storage with Warning of "end of life" the controllers and the event is "The service life of the control module cache battery is 90 percent depleted". The hardware is out of warranty, something can be done to fix without disabling the Warning notification Thanks Regards
Question
•
EqualLogic
Community Accepted Solution
Hi good day, Please help to find out EOSL for below model list; Switch – Dell Powerconnect 6224 SAN storage – Dell EqualLogic PS6100XV
Question
•
EqualLogic
Community Accepted Solution
I have an EqualLogic PS6100, which is out of warranty and we are unable to source replacement drives for. We have recently purchased a new EMC SCV3000, which will replaced the older unit. We are in the process of moving all VM's and data out of the PS6100, but this will take many months to ac
Question
•
EqualLogic
Community Accepted Solution
Hi, I have a 6110XS Hybrid that had 3 SSD drives failed, these disks and also the box are out-off-order by DELL since this storage is out of warranty.. Can I swap-out the remaining SSD disks and leave the storage with 24 SAS disks, so, transforming the storage back to and 6110X only.. will this conf
Question
•
EqualLogic
Community Accepted Solution
Hello Gurus, I have configured controller with dedicated management port. iscsi network is 172.20.10.100 management port ETH4 192.168.200.153 I am able to use GUI and to configure SAN, but have no luck connecting to SAN HQ. I tried both IP and getting error Obviously the m
Question
•
EqualLogic
Community Accepted Solution
Hello,I am administering a network consisting of 14 hosts and 10 EqualLogics. One of our hosts is unable to connect to our SAN. The host is a Dell r710 with ESXI 6.5 U2 and MEM 1.5 installed. The host is assigned to a distributed switch for isci traffic. The uplinks are assigned to the port groups a
Question
•
EqualLogic
Community Accepted Solution
Hi everyone. I have 2 PS4110X in a pool and need to expand my space. Should I buy a extra PS4110X unit as I did before when I only had 1 PS4110X or buy a PS6110X? Regards Olle
Question
•
EqualLogic
Community Accepted Solution
I have 2 Dell PowerEdge R640 servers both running VMware ESXi 6.0.0 5572656. One that is about 6 months old connects to my Equallogic PS4100 without issue, my new one is set up exactly the same but I receive the 7.4.3 login to target failed, reason: "Initiator is not authorized for this target" err
Question
•
EqualLogic
Community Accepted Solution
Hi, My SAN Headquarters is giving me a warning error (Sending e-mail alert), I can't find a way to clear this warning, It happened after adding a new interface to the SAN Headquarters host server, I already corrected the problem but cant find a way to clear this warning.. Anyone can help?
Question
•
EqualLogic
Community Accepted Solution
Good morning All, I would like to know the list of commands available to me to use to troubleshoot a Dell Equallogic member via serial cable when the storage lights are not flashing and the application and browser application are not available as well? Regards Teekash
Question
•
EqualLogic
Community Accepted Solution
I have an old PS4100 SAN replicating to a secondary DC. The SAN contains 7 ESX datastores, they are all replicated and I have been asked to test a restore. Looking in EqualLogic group Manager in the Inbound Replicas list on the target SAN, I only see the option to promote replica sets to volume.
Question
•
EqualLogic
Community Accepted Solution
Hello all,I'd like to know if you guys could help me on it.I have a scenario, where I will add a PS 4100 to my site DR. In my site DR, I have a PS as well and I'd like to make an integration.The purpose of the integration is that I bought a Dell EMC SCv3020, created a new SAN and now I have it as my
Question
•
EqualLogic
Community Accepted Solution
Hi, We have two spare disks in a PS4000 raid. One is marked "spare" and the second became "offline" without any errors. ven-1a34-group1> member select ven-1a34-san1 disk select ven-1a34-group1(member_ven-1a34-san1 disk_15)> show ______________________________ Disk Information _______________
Question
•
EqualLogic