Unsolved
This post is more than 5 years old
4 Posts
0
5782
December 26th, 2003 00:00
LSI U320 Controller Driver for Linux
Greetings!
I realize that Dell customer service doesn't offer any official support for anything but Red Hat, but I'm hoping that somebody over here can help me out. I need a driver to accent my slackware install for the controller in my new PowerEdge 1750. I believe it's the LSI Ultra 320 controller. If anyone has a driver, or can point me to one, or can tell me what the name of it is in the official 2.6 kernel (if it is supported in the kernel), I would be highly appreciative. =)
Thanks!
Message Edited by duerra on 12-25-2003 08:27 PM
No Events found!
duerra
4 Posts
0
December 26th, 2003 00:00
Greetings!
Sorry, I found a better forum to post this thread in: http://forums.us.dell.com/supportforums/board?board.id=pes_hardrive
This one can be deleted, or you can view it there, if you like =)
speedstep
11 Legend
•
47K Posts
0
December 26th, 2003 16:00
This is not a basic controller its an OEM Raid controller. Its not a dell product that I remember. At least mine usually come with an Adaptec PERC2 or PERC3
Product Description LSI Logic MegaRAID SCSI 320-0 - RAID controller - Ultra320 SCSI - PCI 64
Device Type Storage controller (RAID) - RAID - plug-in card
Interface(s) Required PCI 64 / 66 MHz
Dimensions (WxDxH) 6.6 in x 2.6 in
Controller Interface Type Ultra320 SCSI
Data Transfer Rate 320 MBps
Buffer Size 64 MB
Supported Devices Hard drive, disk array (RAID)
Channel Qty 0
Max Storage Devices Qty 30
RAID Level RAID 0, RAID 1, RAID 5, RAID 10, RAID 50
You also havent said if its the model 320 - 0
320 - 1
320 - 2x
320 - 4x
http://www.lsilogic.com/files/support/rsa/txt/lsi_rel.txt
http://www.lsilogic.com/files/support/rsa/txt/rh118j.txt
Megamgr Standard Features:
=========================
-Utility supports 12-adapters including of all types of cards supported by it. It supports SCSI and Intelligent
IDE/SATA MegaRAID cards viz.
428/434/438/466/467/490
471/475/493/511(IDE)/518/520/523(sata6)/Sata4/531/1035
-Utility does now allow Raid-0 spanning.
-Max 40-arrays support on 40-ld card, 8-arrays on 8-ld card
-Spanning across partial arrays are disallowed
-Shows Predictive failure ,if any, in physical drive properties menu
-Utility allows user to initialize OPTIMAL logical drives
-Supports consistency checking of OPTIMAL non-RAID0 logical drives
-Utility does not allow the user to exit the rebuild/check consistency/init progress screen without
aborting the operation.
-Utility allows the user to view ongoing REBUILD on all the physical drives.
-Shows Battery options in MainMenu->Objects->Adapter menu since ver 5.14. Earlier it was available in
Main Menu->Object menu. This is now available only when there’s battery on the adapter.
-Supports Reconstruction (RLM + OCE)
-Ongoing Reconstruction detection and stop other activities on that card till reconstruction is over.
-Supports RAID=0,1,3 (not on U320 controller),5,10,30 (not on U320),50
No RAID 3/30 option on U320 controller.
RAID 3/ RAID 30 is not allowed on SATA cards since ver 5.15.
duerra
4 Posts
0
December 26th, 2003 17:00
If you go to the downloads page, select the following dropdowns:
SCSI I/O Controllers
Ultra320 SCSI I/O Controllers
LSI53C1030
This brings you to a page for driver downloads for Red Hat, SuSE, and Caldera... but nothing for slack, and I don't see source downloads either... but maybe I'm blind (a known possibility) =/
speedstep
11 Legend
•
47K Posts
0
December 27th, 2003 15:00
The Megaraid Drivers seem to be the ones recommended for this.
ftp://ftp.lsil.com/pub/linux-megaraid/drivers/version-2.00.9/