Unsolved
This post is more than 5 years old
4 Posts
0
2163
September 13th, 2013 12:00
Help with initialization of VNX5300
I am arriving on site and power on the EMC 5300 but the boot of the SP looks wrong, this is the message I saw in /var/log/messages:
Sep 13 22:33:31 emcnas_i0 nd-clnt: Connect to server_2b port 5033 failed
Sep 13 22:33:31 emcnas_i0 last message repeated 2 times
Sep 13 22:33:41 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:0b:54 via eth0: network 128.221.252/24: no free leases
Sep 13 22:33:41 emcnas_i0 mcd_helper: Timed out. Giving up
Sep 13 22:33:44 emcnas_i0 mcd_helper: NBS device(s) not available yet...
Sep 13 22:33:44 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:24:62 via eth0: network 128.221.252/24: no free leases
Sep 13 22:33:48 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:24:62 via eth0: network 128.221.252/24: no free leases
Sep 13 22:33:54 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:0b:55 via eth2: network 128.221.253/24: no free leases
Sep 13 22:33:56 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:24:62 via eth0: network 128.221.252/24: no free leases
Sep 13 22:33:58 emcnas_i0 dhcpd: DHCPDISCOVER from 00:60:16:53:0b:55 via eth2: network 128.221.253/24: no free leases
Help me please
Rainer_EMC
6 Operator
•
8.6K Posts
0
September 13th, 2013 14:00
Double – check the cabling
Make sure you install and power on according to the hardware installation guide
eluimel
4 Posts
0
September 13th, 2013 14:00
Hi Rainer
Thank you very much for answer me, I already check the cabling following the Installation Guide P/N 300-012-923 Rev05
Any other idea??
BR;
eluimel
4 Posts
0
September 13th, 2013 15:00
This is the guide that I am following, I am using ethernet cat 5e cables to connect CS0 to the Blade, I am using the conenctor for the B conextion
Rainer_EMC
6 Operator
•
8.6K Posts
0
September 16th, 2013 03:00
The two interfaces that it is complaining eth0 and eth2 are the ones that connect the control station to the data movers.
Either your cabling is wrong, the DME isn’t powered on – my best guess
Make sure you only connect eth3 to the outside network – all others should be internal
Also verify that 128.221.x.x isn’t used in the customer network
If that doesn’t work I suggest to call the EMC support phone or use the customer service live chat
eluimel
4 Posts
0
September 16th, 2013 08:00
Hi Rainer
I just avoid the power connection picture, all is corrected I dont know if you have another advise, which eth3 did you refer?
BR
Rainer_EMC
6 Operator
•
8.6K Posts
0
September 16th, 2013 12:00
There are 4 physical Ethernet ports on the control station – eth0,1,2,3