UNSOLVED

nwm15

updated

20 years ago

N

nwm15

1 Rookie

•

14 Posts

0

3743

January 1st, 2007 00:00

System Loop

I just installed RAM, PSU, and Graphics card. Now when I start up my computer it goes in a loop of the Graphics card info, dell BIOS startup and then the black with white bar system prompt like screen. Sometimes it gievs me a
load needed dlls for kernels message
and then shuts down, back into the loop

What can I do

Message Edited by nwm15 on 12-31-200608:18 PM

  • fireberd

    11 Legend

    •

    33399 Posts

    •

    112848 Points

    404

    0

    Posted January 1st, 2007 09:00

    Only install one component at a time, do not install several as you won't know what is really causing the problem. 
     
    Suggest you uninstall the RAM and video card, leave the new power supply in and see if it works with the original RAM and video.  If it does, then install the RAM and make sure everything works and if it does you can continue on with the new video card. 
    Inspiron 16 5630 Laptop and WD22TB4 Docking Station
    Self-built desktop for recording studio application
  • dunedin

    2732 Posts

    404

    0

    Posted January 1st, 2007 14:00

    If that does not work
     
    "load needed dlls for kernels message"
    This normally needs a "Repair" of XP to fix it.
     
    A repair won't lose any data, other than Service Pack (if not on CD), any Windows Updates and unsigned drivers, which will need to be re-installed afterwards.

    Stay offline to do a repair and do not go online again without a firewall enabled. After repairing XP, install Service Pack (if necessary), firewall and then you must install all Critical Updates next.
     
    How to Repair XP
    Boot up with the XP CD in the drive and let Setup run. Go past the first "R" repair option by pressing Enter just as if you're doing a clean install and you'll eventually come to an option to "Repair an existing installation". Select this one.
     
    http://www.theeldergeek.com/repairing_windows_xp.htm
    Scroll way down page to
    Windows Installation CD - Repair Current Installation
     
  • nwm15

    1 Rookie

    •

    14 Posts

    404

    0

    Posted January 2nd, 2007 00:00

    other than that what can I do to help fix this problem
  • nwm15

    1 Rookie

    •

    14 Posts

    404

    0

    Posted January 2nd, 2007 00:00

    I did install the pieces in sepertly, and did not have this problem untill I installed the RAM. I do not always get the load needed dlls for kernel message, and the computer starts up after multiple reboots and power shut offs, I will try and reinstall the RAM again.

    To adress the second solution, I do not have a windows OS CD, but have DELL OS recovery CD creator. I have not previously made one so if I made one now to restore I don't know if it will solve my issue.

    Tell me what you think.
  • dunedin

    2732 Posts

    404

    0

    Posted January 2nd, 2007 00:00

    No, you can`t do a "Repair" with a Recovery CD.  You need a proper XP installation CD to do it.
     
    If you were to use a Recovery CD it would put your system back to factory settings and you would lose all your data.
     
    Having said that I would advise you to make the Recovery CD anyway as it is your only way to reinstall XP in the future.  If you have a total crash you will not be able to reinstall if you have not made that CD.
  • dunedin

    2732 Posts

    404

    0

    Posted January 2nd, 2007 10:00

    You say it is the RAM to blame.  Maybe you have the wrong type of RAM.
     
     
    You can use either of the boxes on the right hand side
    "Crucial Memory Advisor Tool"
    "The Crucial System Scanner"
     
    Find out the correct type of RAM for your system and also how much RAM the system suppports.

  • nwm15

    1 Rookie

    •

    14 Posts

    404

    0

    Posted January 3rd, 2007 02:00

    I have the right kind, but should I switch slot, from 3 to four, will it make any difference. Both my computer and the scanner reconize the RAm, butthe scanner said that it was PC2-3200 not the PC2-4200 that it is, does this matter.

    Any further suggestions?

    P.S. When I get the computer to finally load it works fine, better than before, abd Battlefield 2 is runnign smoothily at good settings.
  • dunedin

    2732 Posts

    404

    0

    Posted January 3rd, 2007 10:00

    I don`t think that matters as long as you are not mixing different types of RAM
     
    Yes, try putting it in a different slot and see if it helps.
     
    If the machine does eventually run well I can`t think what else to suggest.
    Sorry.