Help

Start a discussion

kevin79

updated

14 years ago

Solved!

Go to Solution
K

kevin79

1 Rookie

•

55 Posts

0

201524

March 20th, 2013 14:00

iDRAC - shared network question

I'm low on network ports in my computer room and want to set up the iDRACs to use the shared network port instead of a dedicated port. If I do this, will the iDRAC work when the server is turned off? What features do I lose if I use the shared network port instead of the dedicated port?

  • DM

    Daniel My

    12 Elder

    •

    6205 Posts

    32232

    1

    Posted March 22nd, 2013 13:00

    Okay, I'm still trying to hunt down a server to test with. I found something else to check while we wait. Make sure your switch is capable of autonegotiating speed on the interface connected to the LOM/s. Let me know what speeds the switch is capable of.

    When the server has AC input power applied but is powered off, LOMs typically negotiate down the external link speed for reduced power consumption while still supporting Wake-on-LAN and/or shared network ports. These re-negotiations can create a momentary external link loss which may or may not interrupt any active remote management connectivity. If a connected switch is configured in a way to not allow for this dynamic speed negotiation, then remote management connectivity may not be available when the server is powered down.
  • DM

    Daniel My

    12 Elder

    •

    6205 Posts

    32156

    0

    Posted March 20th, 2013 14:00

    Hello Kevin

    Yes, it will still be accessible when the server is powered down. The primary negatives are that the available bandwidth for applications on the NIC port that is shared will be reduced  because part of it will be segmented for the iDRAC. Also, if there is an issue with the NIC the iDRAC will be inaccessible. When updating the NIC firmware or applying changes to the NIC iDRAC connection will be lost.

    Also, the dedicated port is a gigabit interface(100Mb on blades). It will be throttled down to 100 megabit when shared.(Edit: This is in regards to 12th generation iDRACs. 11th and earlier are all 100Mb)

    Thanks

  • K

    kevin79

    1 Rookie

    •

    55 Posts

    32232

    0

    Posted March 21st, 2013 06:00

    When you say it will be throttled down, are you talking the data that is transmitted through the NIC for the OS as well?

  • DM

    Daniel My

    12 Elder

    •

    6205 Posts

    32232

    0

    Posted March 21st, 2013 09:00

    The iDRAC will only use a maximum of 100Mb of bandwidth on the shared port rather than the 1Gb it will use on the dedicated. This will also decrease the available bandwidth for the OS on that port, so both.

  • K

    kevin79

    1 Rookie

    •

    55 Posts

    32232

    0

    Posted March 21st, 2013 13:00

    So will the OS have 900Mb instead of 1Gb?

  • K

    kevin79

    1 Rookie

    •

    55 Posts

    32232

    0

    Posted March 22nd, 2013 07:00

    I just tested an iDRAC with a shared card. When the server is off, I can't ping or connect to the iDRAC. Is there a specific setting that I need to configure? The server has the latest firmware (iDRAC - 1.95, BIOS - 2.7.4) and is running ESXi 5.1

  • DM

    Daniel My

    12 Elder

    •

    6205 Posts

    32231

    0

    Posted March 22nd, 2013 10:00

    I just tested an iDRAC with a shared card. When the server is off, I can't ping or connect to the iDRAC. Is there a specific setting that I need to configure? The server has the latest firmware (iDRAC - 1.95, BIOS - 2.7.4) and is running ESXi 5.1
    To my knowledge there is nothing to configure. Which shared mode did you set it to? Did you specify a shared LOM or is it shared with failover? All of the documentation I have read states that the iDRAC 6 express includes power management features via web GUI. Those features include powering on the server. I have not tested this myself though.

    Are you able to access it when the server is on? If we can't get it working then I'll try to track down a server with with an iDRAC express to test with.

    Thanks

  • K

    kevin79

    1 Rookie

    •

    55 Posts

    32231

    0

    Posted March 22nd, 2013 12:00

    Yes, I can get to it when the server is on. It is set to Shared with Failover All LOMs. Changing it to just Shared produces the same results.

  • DM

    Daniel My

    12 Elder

    •

    6205 Posts

    4745

    0

    Posted March 22nd, 2013 13:00

    Thanks for the update! I'm curious, what speed did it negotiate to with the laptop?

  • K

    kevin79

    1 Rookie

    •

    55 Posts

    4745

    0

    Posted March 22nd, 2013 13:00

    I'm not positive but it looked like 100Mb. I didn't really look though since the pings worked.

Dell Support Resources

Latest Solutions

View More