I was doing some preliminary testing on a new MD3000 setup using two SAS 2 port HBAs and 12 disks in the MD3000. I wanted to clear the entire setup and completely start over with all new settings using the Dell Disk Array Management program. I cleared all of the settings using this program and now when I try to add a new array using the automatic search the program does not find any hosts at all. Both HBAs are still listed and working fine in Device Manager. I removed the Dell Disk Management program, installed the newest version, even went to the length of killing/rebuilding the install of Server 2008 Enterprise x64 as this is just a test environment for the time being. Still, no arrays/hosts found by the Dell program.
How can I reset the controllers (the MD3000 has 2 controllers, each with a single In and Out port) to factory specs so that I can detect them in the Dell Disk Array Management program?
Thanks for your input. I found another post that outlined exactly what I needed to do:
From http://en.community.dell.com/forums/t/19192337.aspx:
"If you do want to utilize in-band management also, the "Access" virtual disk will need to be mapped to the host manually since it was deleted. I should note to forum readers that the virtual disk named "Access" is mapped to all hosts and should really not be deleted. To reestablish the mapping of Access to the host first create the host if not already completed. Then go to Configure->Create Host-to-Virtual Disk Mappings, select the host then click Next, select the virtual disk named "Access", change the logical unit number (LUN) to 31, and click Finish."
I created these Access Virtual Disks and the array seems to be a lot happier. I have the array configured and a virtual disk group and virtual disk set up and Server 08 is happy with that. However, the array is still being managed out of band. At the top of the Modular Disk Storage Manager it gives addresses of each controller's IP ad hardware addresses, and underneath that is listed: "In band management connection: None". How do I go about enabling in-band management? I have tried disconnecting the ethernet cables from each controller, resetting the Modular Disk Storage Manager Agent in Services, even rebooting the server itself and the Dell Modular Disk Storage Manager can never find the array unless the ethernet cables are reattached.
Should have mentioned I was using in-band management, so no networking required on the hosts. Any way to reset without assigning IPs to the lan management console ports? I can resort to this if necessary but would prefer to keep it in-band.
In-band management? Out of band management? It sounds like the reset set the IP addresses back to default, or possibly cleared. But you will have to get the management working first to investigate it further.
When setting up MD3000i's, I usually use a laptop to set the IP's to what I need them to be, before connecting hosts or management ports to our LAN.
I first need to know how you cleared all of the settings. Did you do this via the Modular Disk Storage Manager GUI or CLI? In the CLI there is a "clear"command which is the easiest way to clear the configuration of the array. If you used the GUI one has to go step by step.
Also, by automatic search of hosts do you mean that you're trying to discover the storage array? The GUI does also auto discover attached host servers, thus it does matter.
Please do this. From the base directory that you installed the MDSM software at there's a "util" directory (this is not applicable for a "Management Station" only install). Run the SMdevices batch file and copy the output into a post. The output should contain a listing including LUN 31 for each physical SAS connection between the host server and the array, similar to:
\\.\SYMsmUTMLun1 [Storage Array MD3000, Virtual Disk Access, LUN 31, Virtual Disk ID <6001422000fff0380000000000000000>]
Thanks for the response. I understand that in-band is not necessary, but in the environment that this server will be used I'd prefer to go with in-band only (with out of band as an option if need be) management. Is there a way to switch from using in band only to out of band only?
The SMdevices output would have easily clarified this, that said it does appear that the Access LUN mapping was manually deleted in the GUI. FWIW the ability to inadvertently remove the Access LUN mapping to the Storage Array was removed in the Generation 2 update.
To be clear In-band management is not required if out-of-band is already being used, although it is recommend in the documentation.
To use in-band management the management station on which MDSM is being run on needs IP connectivity to the host server(s) that are connected to the array. If the management station is on the same subnet the in-band agent (SMagent) on the host can be discovered automatically, if it's routed than discovery must be done manually.
You do not need to disconnect the Ethernet cable from each controller, that has no impact on in-band discovery.
Well in that case discover the in-band management path and then simply remove the Ethernet cables from each controller.
If you only want to see in-band on the Summary tab then first Remove the array from MDSM, remove the Ethernet cables from each controller, and the discover the array.
Got it! Once I was able to re-add the Virtual Disk mappings for the "Access" disks on each controller I was then able to remove the ethernet cables and refresh the config and it is all being managed in-band at this time.
The idea of requiring "Access Virtual Disks" is kind of beyond me but now that I know how it all plays together it makes some sense ;-)
VG! I'm glad your storage array is all set. You're very welcome. ;-)
The "Access" disks are simply how the host can talk to the control plane (i.e. managment) of the array. It's the mechanism by which the storage array gets it managment commands to the array via the SAS connections.
I tested md3000 and deleted (there are notice regarding it :emotion-6: ) "access" disk form management by mistake and lost access to the unit. How I can restore it? Please help. The host server directly connected to storage with sas raid controllers.
Brad S.
5 Posts
4702
1
Posted February 24th, 2009 08:00
dzenz,
Thanks for your input. I found another post that outlined exactly what I needed to do:
From http://en.community.dell.com/forums/t/19192337.aspx:
"If you do want to utilize in-band management also, the "Access" virtual disk will need to be mapped to the host manually since it was deleted. I should note to forum readers that the virtual disk named "Access" is mapped to all hosts and should really not be deleted. To reestablish the mapping of Access to the host first create the host if not already completed. Then go to Configure->Create Host-to-Virtual Disk Mappings, select the host then click Next, select the virtual disk named "Access", change the logical unit number (LUN) to 31, and click Finish."
I created these Access Virtual Disks and the array seems to be a lot happier. I have the array configured and a virtual disk group and virtual disk set up and Server 08 is happy with that. However, the array is still being managed out of band. At the top of the Modular Disk Storage Manager it gives addresses of each controller's IP ad hardware addresses, and underneath that is listed: "In band management connection: None". How do I go about enabling in-band management? I have tried disconnecting the ethernet cables from each controller, resetting the Modular Disk Storage Manager Agent in Services, even rebooting the server itself and the Dell Modular Disk Storage Manager can never find the array unless the ethernet cables are reattached.