Solved!
Go to SolutionM
mgiammarco
1 Rookie
•
29 Posts
0
11249
October 18th, 2018 02:00
Cannot close case cover on Dell T5600
Hello,
I have put an Nvidia Inno3d video card inside T5600. When I close the case cover I see that it has an handle that pushes down the video card. But unfortunately the video card has the 6 pin power connector just under the handle so I cannot close the cover.
What can I do?
Thanks,
Mario
9085
0
Posted September 19th, 2019 23:00
Hi again @mgiammarco ,
You can locate them from Technical Specifications section in the Owner's Manual, like this for T5810. However, most of them simply describe it as "Full Height Supported" and not as detailed as those in T5600.
I further searched and see if any handle bar inside case cover for models you mentioned, and the answer is Yes!
T5810/T7810: 0'12" of this video
T5820/T7820: 4'09" of this video
You will have to deal with same problem as what happened in T5600. Better choose card with specific small size of height.
9402
0
Posted October 19th, 2018 03:00
Probably I have not explained well because I am not english native but for case cover I mean the lateral case panel with the handle you can pull to open.
Is there a low profile 6pin extension cable? Is it possible that this thing is happened only to me?
Thanks,
Mario
9372
0
Posted October 21st, 2018 22:00
You did fine; I could easily understand your first post. Have you tried eBay or Amazon for the cable you're looking for? "90 degree plug" as part of your search term could help too.
9352
0
Posted October 22nd, 2018 11:00
Thanks for reply!
Meanwhile I have ordered this I hope it will be enough: https://www.moddiy.com/products/PCIE-90%C2%B0-L%252dShape-Mini-Low%252dProfile-GPU-Power-Cable-%286%252dPin-Up%252dAngle%29.html
I still do not understand Dell choice considering that I see now that most graphic cards have power connector over the top!
9279
0
Posted October 28th, 2018 23:00
I'm glad you were able to find a cable for it. Did it work?
9061
0
Posted January 19th, 2019 14:00
Yes it worked!
9056
0
Posted January 19th, 2019 15:00
Glad you got it working.:Smile:
8204
0
Posted September 18th, 2019 12:00
I "open" again this thread.
Assuming I will now change my T5600 with a T5810 or T7810 or t5820 where can I find the documentation about max supported height?
Thanks again.
Mario
2328
1
Posted September 23rd, 2019 01:00
Thank you very much for so detailed reply!
bmcowboy
4 Apprentice
•
573 Posts
9167
0
Posted January 13th, 2019 23:00
Hi @mgiammarco,
It's been almost 3 months since you post this thread and hopefully the problem already solved. Meanwhile, I'd like to share my experience in case someone looking for an answer on this kind of problem.
When I first get my T5600, I tried install a GTX 960 as testing. The original design of the cover handle was to tighty hold all expression cards and make them safe. However, it led me to the same problem that cover failed to be closed.
After looking at Technical Guidebook, it stated the maximum height of expansion cards being accepted: 111.3mm
As I planned to buy a RTX 2070 for it and no low-profile model exist in the market at that moment, I made research for all brands and found only Zotac fits: 113mm, slightly higher but marginally OK.
Besides, if you plan to replace a brand new PCIe display card, suggest to choose a full length model. Yes, I'm talking about card length now, not height. It's because most full length display card with their power connector located at the end of the card. In other words, it won't jammed with the cover handle indicated as red rectangle below.
Enjoy!