Hi again Mario

Thanks for the feedback, great that you managed to re-enable the

Could be bad news about the missing NTLDR file?

I’m assuming you have changed BIOS device boot sequence back to normal settings?

And the primary HDD (where boot loader files are located) is drive 0 (zero)

If correct then other common causes are either:

1. Hardware – bad/damaged Hard Drive Disk (HDD) sectors or loose HDD/mobo cable connection

2. Software – missing/corrupt Windows XP boot loader files (includes the NTLDR file)

Sorry but as previously mentioned, you really do need to source the Dell OEM CDs/DVDs that should have been supplied with computer purchase

Assume the editing of MBR partition table did point to the recovery image partition, if correct & the DSR image was restored then it tends to point to bad HDD boot sectors or cable issues?

Check cable connections

If you don’t have the Dell OEM Resource CD to run hardware diagnostics, download diagnostics utility, install on your bootable USB drive & run diagnostics to check HDD

If it were just a software related problem then you could either use Windows Repair Install or copy NTLDR & other boot loader files from XP CD to your primary HDD XP OS partition

But then you don’t have the Dell OEM XP CD!!!!!!!

You havent got a pen drive in the USB socket have you lol- try this http://www.computerhope.com/issues/ch000465.htm

I wrote this in another question you had.

This can happen when the DSR doesn't go back to a seal state.  With the dsrfix used in DOS was another

file called     "PTEdit"     which looks something like this

                                               Type             Boot       Cyl

                               1              DE                00

                               2              07                 80

                               3              DB                00

                              4              00                  00

Do NOT change anything in the other columns but check that  #3  is set to DB for type and the Boot is set to 00.

Check #2 for the 80 in the Boot column this sets that partition to active so it boots and not PBR3. You can only have ONE of the 

4 partitions set to active. If as I think your #3 is set to 80, change it to 00 and change #2 to 80, or set like above and it should boot

the correct partition.   Hope this helps.

Hello Bell Boy

I have no words to thank you for your kind attention.

Ok please help me clear my stormy mind, let’s see:

You mentioned if I have changed BIOS device boot sequence back to normal settings.

I tend to think yes, but again I’m not completely sure.

In the boot set up (where there is a tiny list with: floppy, hard drive, cd-rom, usb) as I understand the numbers are the order the computer will try to boot, beginning from number one till if finds a bootable source.

Number one is placed to the hard main hard drive, but there is no number so I could be sure if it´s drive (0) zero.

I don’t think there is a damaged HD or cable problems since I’m using the computer right now to write you, so it did boot XP and its working fine so far.

So ok I never got any CD´s for this computer from Dell

(I still have this fool piece of cardboard printed with a CD shape and the proud Dell logo, saying this computer does not need any CD¨s Grrrrr)

So how can I get out of this dead end, is there a place where I can download this CD´s?

I have tried contacting Dell here in Mexico and If I’m not under guaranty time I can have no assistance, help or information at all, not even paying, (which I find very rude by the way)

So I feel lost, frustrated and really confused.:emotion-6:

With Goodells DSRFIX I got this:

*good : boot code matches dell mbr v3.

*good : pbr descriptor 1 is type DE.

*good : pbr descriptor 2 is type 07.

*alert:  pbr descriptor 3 is type OC and not DB.

*Info : pbr descriptor 4 is type 00.

*good: pbr1 is fat16, label is dellUtility..

*good: pbr1 is fat32, label is dellRestore.

*good : reference partition table in sync.

Of course I don’t understand what this means, but probably you can see something in here.

I really liked Windows 7 a lot but if I had known this would have happen I would have never ever installed it.

Again I have no words to thank your help

Mario:emotion-2:

Hello Tom

Thank you so much!!!

I have just ran the PTEdit again.

I did disconnect the secondary HD and also the external one just to be sure.

So this is what i got:

there are two drives in the PTEdit, I assume one of those drives is the USB pen drive where I’m booting from.

so the power Quest Partition Table Editor says this:

__________________________________

DRIVE 1 (1927MB)

        TYPE      BOOT      CYL

1        OC          80

2        00           00

3        00           00

4        00           00

Partition Information Fat32 bootable 1927MB

__________________________________

DRIVE 2 (152586MB)

        TYPE      BOOT      CYL

1        DE          00

2        07           80

3        DB          00

4        00           00

Partition Information 31MB

__________________________________

So I suppose the drive 2 is the real main HD no?

It seems to be in the way you suggested.

Have tried running again the DSRFIX /F and chose to fix the recommendations, but it remains as the report i sent previously it does not seem to be able to go beyond this point.

Thanks so much beforehand

Mario

Mario

With Goodells DSRFIX I got this:

*good : boot code matches dell mbr v3.

*good : pbr descriptor 1 is type DE.

*good : pbr descriptor 2 is type 07.

*alert:  pbr descriptor 3 is type OC and not DB.

*Info : pbr descriptor 4 is type 00.

*good: pbr1 is fat16, label is dellUtility..

*good: pbr1 is fat32, label is dellRestore.

*good : reference partition table in sync.

I think you need to run the dsrfix /f again and answer yes to all questions.

The alert pbr descriptor 3 is 0C and not DB.

the line that said *good pb1 is fat32, label is dellRestore should have been pbr3.

Check again.

Once you get this all showing good the Ctrl F11 should work and restore the image.

Once that is done, if the system doesn't seal you will get the PBR3 done again.

You will need to use the ptedit and set the third partition Type to DB and the boot to 00.

Them set the second partition type to 07 and the boot to 80.

Then boot, should work.

Hi Mario

The second drive is the real drive and looks good.

Have you did a restore yet with ctrl +F11 ??????

You might need to remove the usb drive to let the real drive c boot first.

Let me know what happens.

Mario

Having multiple threads running makes continuity in replies confusing

Drive 0 (zero) is under Drives NOT Boot Sequence

When using Clean Install, DSR or Repair Install options you must disconnect all peripheral devices (includes e.g. NIC adapter cable) before initiating any reboot wipe options (excludes monitor/keyboard/mouse)

Suggest you only have the USB flash drive connected when using dsrfix then when finished, remove it & then reboot to System Setup (BIOS) to restore Boot Sequence back to default, then exit saving settings

When using dsrfix did you try the DSRFIX /F /81 command??

Hi Again Tom

Thank you so much.

So I ran again the DSRFIX and this is what i got.

*good : boot code matches dell mbr v3.

*good : pbr descriptor 1 is type DE.

*good : pbr descriptor 2 is type 07.

*good:  pbr descriptor 3 is type DB.

*Info : pbr descriptor 4 is type 00.

*good: pbr1 is fat16, label is dellUtility..

*good: pbr1 is fat32, label is dellRestore.

*good : reference partition table in sync.

Ready to queue changes…

No changes queued.

This last part of the queued changes, is normal or does it means something went wrong?

I still don’t know what this means: the line with "info" does this means an error, or just that there is no 4th partition?

Im now afraid to hit the Ctr+F11 the last time I made this i got:

PBR3 done

NTLDR is missing

hit any key to restart

But it does not restart but just returns to the same message endlessly and shutting it off works for nothing since once turning it on again it goes back to the same loop.

I was suffering a while ago to be able to get it booting normally again took me a few hours

So probably with this new DSRFIX info you might be able to tell me if my next intent could be a bit more successful

Thank you so much again

Mario

Im very sorry!

in my previous post there is a mistake:

where it says:

*good: pbr1 is fat32, label is dellRestore.

it should say:

*good: pbr3 is fat32, label is dellRestore.