Hi there,

I gave that a second thought and I'm really not sure if I did that in the past. I may be mix that up with another box or so.

Thanks anyway

Jan

I was unaware that was possible, but given that whole config is part of autosupport I always relied on autosupport entries.

Maybe you had EMC EDL before, that used to have a "save configuration" button and "take X-ray" in the GUI.

As above, the Autosupport has everything you need for the configuration.

Regards, Jonathan

Not possible. I've repeatedly complained about this.  What I did was set-up my own method.

For this you need to set-up the ability to run DD commands remotely using SSH - there is a technote on how to do this. Once SSH is in place you can do a lot stuff with DD command on the remote box and script what you require.  This script is for an older version and requires the mutt mailer to be installed plus sendmail to be configured on the linux box where the script is run. Only tested and run on RHE.   Because upgrades usually alter the output commands its likely to break the -check option.  Should be good enough for a weekly dump of a later version.

#!/bin/bash

# Only applicable for 5.2.x.x

# Obtains the configuration from the Data Domain systems 

# The default action is to get the configuration from the systems and mail to the shared admin mailbox

# Could cron this for a weekly run

# This script will detect configuration changes requires the -check switch 

# If provided with the "-check" parameter this script  will compare the configurations with previously recorded

# configurations.  If they have changed the new configuration is sent to the $CONFIG_RECEIVERS mailbox(es)

# and a change notification is sent to the CONFIG_NOTIFY_RECEIVERS mailbox(es). No change no mails.

# Could cron this for a 1 or 4 hourly/daily run

Hi ,  Jim' script seems nice ,

But you can also as mentioned use the autosupport feature ,

I use this to save the config:

Putty to the DD box: 

Under settings in putty  i log all output  then i login as Sysadmin in DD-box and save output of this command:

#config show all

There you have IP-config , admin access , replication , cleaning  etc.

Do not realy see the point by saving audit log information as a part of D/R backup of the DataDomain config system,  You'r script is neat but I think also an overkill for what information JayJay wish to save.

#config show all      answers all the questions the thread-starter asked about,  Backup of IP config and NTP config settings.

Realy dont understand what you mean "it contents can change every time you run it"   If you have made any config changes ofcourse it will show those changes , If you have made no config changes  #config show all   will give you same output every time as designed.

Anyway ... If you come to a point in life where you have to use this information you have backed up and re-install the DD system .. I feel more sorry for your data protected by the DD box then the config it self.   I use this #config show all   as a cheat-sheet if I need to set up several DD systems at the same location.

I found "config show all" too basic for what I wanted, plus its contents can change every time you run it.  Being dynamic not useful for detecting change.  With individual commands you eliminate the dynamic components, plus the script output provides provide about 3x the contents of "config show all"   Example - I found somebody creating an admin account when they did not have the authority to do so.  The only problem will when I do a firmware upgrade the script will have to repaired.

Hi Jan,

Please refer to this KB.

How to Back Up Your DD Configuration

Hope this helps!

The best place I have found the minimum requirements for DR is in the System Controller Upgrade Guide it recommends running autosupport send username@yourcompany.com plus other commands on pages 13 - 16 to record the current config in case of a disaster.  Some of the commands actually stop stuff as a part of the preparation process, probably not a good idea to run those.

Apparently the head swap process saves the config onto external disk in the disk enclosure.  Is there a method of dumping the config  to there as a regular part DR in case the controller dies?  

We are upgrading DD , could someone please help us know prerequisites and precautions that we need to take care?