Ok so I bought a new video card off of dell recently for my father's computer ( the card is a Stealth s80 featuring radion 9200 se and his computer is a Demension 2400) I and I also got one for mine. I had problems installing mine which i finaly worked threw but i skipped some steps on accedent which I had to go back and fix later. Well I figured I wouldn't skip the steps when installing my dads. One of the steps before installing the card itself was disabling your previous graphics card. In doing so I disabled the monitor (without realizing it) in Device manager. When we botted the computer up we realized that the monitor was't working. We've tried a lot to fix it but it just doesnt work because me can't see. Is there any steps we can take to renable the old monitor? The only other solution we can think of is formating the hardrive, but a dell is a little differnt than are old computer so what steps would we take to formate it if required?
So it looks like you disabled the built in graphics adapter from the system, which disabled your display. (assuming you had intergrated graphics)
Have you gone in the bios settings to see if you can manually turn the original graphics adapter.
Though, I don't see what the problem is. I would think all you'd need to do is install the card, connect the monitor to that, then start up the computer and it should work, but it will be slow and in low res until you install the video card drivers, then restart.
It's not really hard to or complicated to put a new card in. Kind of uninstall drives of current card, shutdown, replace card, startup, install new drivers. Though, I will agree it can get a little buggy with an intergrated adapter in the mix.
EDIT: Oh, to get into the bios it's usually the delete key when it says to do so or while during the dell splash screen.
Message Edited by TimothyBH on 01-21-2005 11:49 PM
I looked at bios briefly on my comp and didn't see it. The thing is the card isn't plug in play. I need to load up windows and then install it threw a disk. Thats kinda hard to do if i can't see the monitor. Basicly I made the mistake of disabling the integrated graphics or w/e before I installed the new card.
I would think all cards are plug and play to a sense of a basic opperating level, where you start up at 640*480 with no acceleration or features. Maybe there's something different going on with brand name machines compared to custom built machines that I have experience with.
So out of curiosity what happens when you install the card and connect the monitor to it and start up, do you get any picture at all?
My experience has always been uninstall all drivers and apps from the previous card, shutdown, install the new card, then start up with the new card, you'll be at 640*480 with low colors, install the drivers, then restart again, and you'll be able to change the resolution and colors back to normal, if it doesn't already do that for you.
I had bought a X800pro once, and I sold it without having a new card yet, so I had a computer with no video card or intergrated video, if it was like you said, I'd be in trouble. But once I got a new card, it was plug it in, start up and install drivers.
Sorry if I'm being a bit one sided. Maybe post the instructions to make it more clear. Oh, and what system your on.
If you don't get much more help besides me, maybe try visiting www.hardforum.com, plenty of PC people there .
Message Edited by TimothyBH on 01-22-2005 03:28 AM
Message Edited by TimothyBH on 01-22-2005 03:29 AM
Message Edited by TimothyBH on 01-22-2005 03:31 AM
Yay! I removed the card and tried to start up the computer luckily the monitor worked! It was using basic stuff like you said. I reinabled the monitor so its like I never touched it. But then I tried putting the card back in and starting. monitor didn't work. I think there is something wrong and it is conflicting with the normal drive which is what caused all this trouble. I'm probly going to end up emailing the card's maker and asking them for help.
Thank you for all your help! It is greatly appreciated!
Still not clear about something. Are you plugging the monitor lead into the VGA plug of the new card? Even without the proper drivers for the card, you should get an image plugged into the new card. If the card is seated properly, and your plugged into it (not the original monitor plug), and you're getting black screen, would say the card must be faulty.
TimothyBH
127 Posts
229
0
Posted January 22nd, 2005 03:00
Message Edited by TimothyBH on 01-21-2005 11:49 PM