How can I install this printer to other PC's on my wired or wireless network without moving the printer or buy a super long USB cord? When I installed it to my one laptop I had to use the disk. I can put the disk into the phyiclly I need to install it on but I can't hook it up directly unless I physically move the printer or get a very long USB cord. Any suggestions. BTW the disk will instruct you to hook the printer directly to the PC. This kind of defeats the purpose of having a wireless printer. Thank you all for your help in this matter.
Use the laptop to setup the printer. I use a 3300 print adapter with my 964 and it sits in a special spot. have 3 laptops that can print to it. Installed the drivers in each. Here are the instructions to setup your printer..
How are you connected to the printer? wired of wireless?
If wired, disconnect your printer. Go to start/programs/Dell printers and un-install your printer.
Restart your computer.
Now go to drivers and downloads/select product/printers/select your printer. Download drivers, Utilities, firmware and Patches.
Install your printer. You'll be prompted when to connect it.
If wireless, fix your network first.
Update the firmware in your wireless router. Manufacturer's website, make & Model needed.
Broadcast SSID(You may want to change this to make it easier to connect)
Use WPA security
Mixed b and g mode(n if available)
Use channels 1, 6 or 11. Most devices work better on these channels.
After router is done, now setup your wireless print server/printer.
If wireless printer server is used, Plug USB cable into computer and print server. Insert the print server disk. Choose Network, then choose print server and follow the instructions.
Now setup the printer.
Now go to drivers and downloads/select product/printers/select your printer. Download drivers, Utilities, firmware and Patches.
Install your printer. Choose Network. Install the drivers.
Rick thank you so much for your reply. The way I have everything set up is-The printer is set up as wireless. The PC that I want to set up next to have access to this printer is hard wired into the wireless router. It is a 2WIRE Modem/router that came with my AT&T Uverse service. It works the same as the 2WIRE wireless router that comes with the AT&T DSL service. I can set up my other laptop because I can move it to the printer. So you see, it is wireless and hardwired in my network.
From what I can figure the only thing that the USB does is connect to the PC so it will recognize the printer. I am hoping that I can do this wirelessly. I hope this all helps. The reason I put all this in here is that it will be hard to follow the instructions as written as portions of both are correct. I hope I am getting all this where you understand what I'm up against. Thank you again for your response.
Model XPS Studio 420 OS Windows Vista Home Premium Processor Intel(R) Core™ 2 Quad CPU Q6600 @ 2.40 GHz Hard Drive 320 GB NCQ SATA (7200) W/DATABURST Memory 3GB DDR2 SDRAM @ 667MHZ-2X1GB Card reader MEDIA CARD READER W/INT BLUETOOTH Anti-virus TRENDMICRO 14.7 PC-CILLIN Network WIRELESS NETWORK CARD 802.11G / WIRED NETWORK ON MOTHERBOARD Software MICROSOFT OFFICE SMALL BUSINESS, DIM Sound card SOUND BLASTER X-FI XTREME MUSIC Internet AT&T DSL
Most people have a desktop that's wired and on 24/7 They hook the printer up to their desktop using the USB connection. They then share the printer with the others on their network. I found this article that might help you.
Since you're using Vista, this may also help.
Printer Sharing on XP/Vista Network
Go to Control Panel. Choose printer. Then choose Add Printer.
Choose Add a local printer. Click on Create a new port. The default in the drop down box is Local Port. Do not change that. Click Next.
A dialogue box will appear asking for you to enter a port name.
Pretty Simple!! if you already have the printer hooked up to one of the PC's.... Just print the N/W configuration page from the printer itself and look for the IP address!
Guess you have to press down arrow ~>Setup~>Network settings ~>Print N/W page on the printer (I'm not very sure about that).
Once you have an valid IP, see if you can ping it from the computer that you want to install If yes, then it should be a peice of cake. Let me know whats up with these steps and I'll reply back based on your reply!
- DMT.
Message Edited by drugmetwice on 02-26-2008 07:51 AM
Please make a new post and tell the make and model of the printer and how you're trying to connect your 948 printer. Using the wireless card in the printer or a wireless print server.
PudgyOne
11 Legend
•
30315 Posts
•
106638 Points
419
0
Posted February 13th, 2008 22:00
Use the laptop to setup the printer. I use a 3300 print adapter with my 964 and it sits in a special spot. have 3 laptops that can print to it. Installed the drivers in each. Here are the instructions to setup your printer..
How are you connected to the printer? wired of wireless?
If wired, disconnect your printer. Go to start/programs/Dell printers and un-install your printer.
Restart your computer.
Now go to drivers and downloads/select product/printers/select your printer. Download drivers, Utilities, firmware and Patches.
Install your printer. You'll be prompted when to connect it.
If wireless, fix your network first.
Update the firmware in your wireless router. Manufacturer's website, make & Model needed.
Broadcast SSID(You may want to change this to make it easier to connect)
Use WPA security
Mixed b and g mode(n if available)
Use channels 1, 6 or 11. Most devices work better on these channels.
After router is done, now setup your wireless print server/printer.
If wireless printer server is used, Plug USB cable into computer and print server. Insert the print server disk. Choose Network, then choose print server and follow the instructions.
Now setup the printer.
Now go to drivers and downloads/select product/printers/select your printer. Download drivers, Utilities, firmware and Patches.
Install your printer. Choose Network. Install the drivers.
Everything should now work.