UNSOLVED

58doozie

updated

21 years ago

5

58doozie

4 Posts

0

14025

May 31st, 2005 06:00

CD-ROM Replacement Problem

 

After installing a replacement CD-ROM that Dell sent me, my CD-ROM drive D has disappeared and also my CD-RW Drive has disappeared.

I followed instructions in my Owners Manual for adding a CD-ROM drive since Dell did not send me instructions and I could not find any.

It was after my warranty expired that I was informed they kept sending me a differnt part because they no longer had any like mine. So, they would not send someone to install this for me.

What now?

I did the BIOS update again.

I cleared NVRAM.

These did not help.

 

Original CD-ROM:  HL-DT-ST- CD-ROM GCR-8483B

Replacement CD-ROM:  CD, 48X, F5, SMSNG, SC148A, 01, V2

Dell Dimension 2400

Intel Pentium 4

 

Drive configuration:

 Diskette Drive A                    3.5

 Primary Master Drive            Hard Drive

 Primary Slave Drive               OFF

 Secondary Master Drive            Unknown Device

 Secondary Slave Drive            Unknown Device

 

IDE Drive UDMA                       ON

 

Boot Sequence:

1.      Diskette Drive

2.      Hard Disk Drive C

3.      CD-ROM Device (Not Installed)

 

Thank you!

 

Deb

  • Predator

    2 Intern

    •

    15286 Posts

    271

    0

    Posted May 31st, 2005 12:00




    Hi Deb,

    Did you set the jumper on the new drive to Cable Select, double check this OK?

    Click on the CD/RW link in my post and scroll to Section 20, article 3 and Section 12, article 10. See if either of these helps if it is not a jumper issue.

    Best Regards




    God, grant me the senility to forget the people I never liked anyway,
    the good fortune to run into the ones I do and the eyesight to tell the
    difference.



    CD/RW Link

  • 58doozie

    4 Posts

    271

    0

    Posted May 31st, 2005 18:00

    Jeff,

    I will see if I can locate the jumper on the new drive and cable select.

    Section 20, Article 3 - There are no red X's and no yellow !. Secondary has disappeared also. Do I uninstall the primary?

    Section 12, Article 10 - I don't have Roxio. No upper filters on the list.

    I'll let you know about the jumper :smileyhappy:

    Thank you!

  • enigma-2

    1 Rookie

    •

    238 Posts

    271

    0

    Posted May 31st, 2005 20:00

    All drives sent out by Dell come pre-configured for cable select (CSEL).

    You can check this by looking at the back of the drive. On the right is the power supply connector. To its left is the 40 conductor data connector. Left of this is the jumper selector. CSEL is jumpered on the "C" and "S" pins at the left of the jumper.

    More likely you need to check the 40 conductor ribbon cable.

    The cable has a colored (usually red) stripe running along one edge. The side with the colored stripe must be plugged in to the connector on the drive at pin number one location (which is right next to the power connector).  So the striped side is connected to the drive connector next to the power supply connector.  (Also check to see that the 40 conductor cable is properly connected to the motherboard & didn't come loose during the change.)

    Dennis

  • Predator

    2 Intern

    •

    15286 Posts

    271

    0

    Posted May 31st, 2005 23:00




    Hi Deb,

    No, do not uninstall the Primary IDE channel.
    If the jumper is set correctly.
    Shut the system down, open the case and disconnect both drives including the power cable as well. Turn your system on, let Windows load, then shut her down once more.
    Now attach the new drive only to the "End" connection of the IDE cable, re-attach the power cable, boot your system and post back the result. If it works, try your second drive, if it does not work, try your second drive on the "end" connection.


    Best Regards




    God, grant me the senility to forget the people I never liked anyway,
    the good fortune to run into the ones I do
    and the eyesight to tell the difference.



    CD/RW Link

    Message Edited by Predator on 05-31-2005 08:52 PM

  • Predator

    2 Intern

    •

    15286 Posts

    271

    0

    Posted May 31st, 2005 23:00




    Actually Dennis, some Members have stated the replacements drives have had their jumpers on Master / Slave or Cable Select, so one cannot assume Cable Select anymore, but I agree with you one would think they all would be come as Dell ships their factory installed drives.
    As for the IDE cable 40-pin, 80 conductor type...



    Best Regards




    God, grant me the senility to forget the people I never liked anyway,
    the good fortune to run into the ones I do
    and the eyesight to tell the difference.



    CD/RW Link

    Message Edited by Predator on 05-31-2005 08:48 PM

  • 58doozie

    4 Posts

    271

    0

    Posted June 1st, 2005 19:00

    Jeff & Dennis,

      Woo Hoo! I re-checked the jumper and cable and discovered one of the pins on the drive was a little bent so it was not attached completely! Thank you, a great reminder to double check things :smileywink:

    So far it is working.

    Thanks once again!

    Deb

  • Predator

    2 Intern

    •

    15286 Posts

    271

    0

    Posted June 2nd, 2005 12:00




    Glad to hear you fixed it Deb, congrats on a job well done !!

    Best Wishes





    God, grant me the senility to forget the people I never liked anyway,
    the good fortune to run into the ones I do and the eyesight to tell the
    difference.



    CD/RW Link

  • 58doozie

    4 Posts

    271

    0

    Posted June 3rd, 2005 03:00

    Thank you Jeff :smileywink: