UNSOLVED
R
riptidemen
9 Posts
0
1979
August 13th, 2007 11:00
Problems mapping disk through the command line.
I was trying to map some disk through the command line but i got an error.
bash-2.05$ sudo symconfigure -sid 0313 -f 20070810_cdmaimg2_map_0313.txt preview
Execute a symconfigure operation for symmetrix '000290100313' (y/ ) ? y
A Configuration Change operation is in progress. Please wait...
Establishing a configuration change session...............Established.
Error occurred while Defining change number 1:
The tid value is invalid
Device 011E generated the failure
Terminating the configuration change session..............Done.
The configuration change session has failed.
I check the script and is good, but the session fail.
Help me...... Thanks in advance
bash-2.05$ sudo symconfigure -sid 0313 -f 20070810_cdmaimg2_map_0313.txt preview
Execute a symconfigure operation for symmetrix '000290100313' (y/ ) ? y
A Configuration Change operation is in progress. Please wait...
Establishing a configuration change session...............Established.
Error occurred while Defining change number 1:
The tid value is invalid
Device 011E generated the failure
Terminating the configuration change session..............Done.
The configuration change session has failed.
I check the script and is good, but the session fail.
Help me...... Thanks in advance
596
0
Posted August 13th, 2007 15:00
can you post content of your map file ?596
0
Posted August 13th, 2007 15:00
Well riptidemen - you've interrupted my coffee break but I've moved your thread anyway. I'll be curious to know why you posted in the coffee break social space forum?
Thanks Hrvoje for noting it.
Julie596
0
Posted August 14th, 2007 05:00
i can't ..government agencies will be after me596
0
Posted August 14th, 2007 05:00
DYNAMOX C'mon !! Introduce yourself at the coffee break !!596
0
Posted August 14th, 2007 05:00
Riptidemen .. as Dynamox said we can better help you if you show us the failing script.
Let me guess .. Are you using SymCLI 6.4 (or later) ?? I've seen big changes in the parser of symconfigure commands with S.E. 6.4 .. maybe you have to put an explicit TID in each command in the failing script.. But as I said before, it would be a lot better if we can see what gives errors.596
0
Posted August 14th, 2007 06:00
Hi!!!!, we are using 6.3.2 Solutions Enabler Software, the script is follow
map dev 011E to dir 08A:1, lun=001;
map dev 011F to dir 08A:1, lun=002;
map dev 0434 to dir 08A:1, lun=003;
map dev 0437 to dir 08A:1, lun=004;
The OS used is Solaris 9. And we never used TID value.
Thank, and sorry about The Coffee Break...this my first time here....
Message was edited by:
riptidemen596
0
Posted August 14th, 2007 06:00
remove the "," after 08A:1
should be like this:
map dev 011E to dir 08A:1 lun=001;352
0
Posted August 14th, 2007 07:00
I have tried making the script with the ",' and without including the target and it works, I think the problem is other, maybe the available lun id as Ryderp told before.
Therefore, I have a question about this luns id, when I mapp through the command line I always use the command:
symcfg -sid #### list -FA all -address -available
For checking the avaliable address, I have a doubt on this now that Ryderp puts the command referring to a specific FA and PORT. The available luns ids are for each FA and PORT? I mean, can I have the lun=001 available for each FA and port or there is ONLY ONE lun=001 in the box and this lun=001 can be used only once?596
0
Posted August 14th, 2007 07:00
The "," fools the parser .. and forces the "symconfigure" command to search for a "TID" value that can't be found in the lines, as Dynamox said.
ble1
6 Operator
•
14354 Posts
•
56186 Points
596
0
Posted August 13th, 2007 14:00