UNSOLVED

audiomarkg

updated

21 years ago

A

audiomarkg

13 Posts

0

36149

May 25th, 2006 13:00

Dimension E510 Processor

I see that Dell is offering the Intel D 900 series processors to the E510 BTO Option. My system is the E510, DM051. Should I assume that the current BIOS A05 will support the new processors in my machine? Anyone tried to upgrade from the D820?
  • Rmdefi

    19 Posts

    506

    0

    Posted May 25th, 2006 19:00

    noobie here, but if your bios uses the 945G chipset, it should handle D processors.

    http://www.intel.com/products/chipsets/945g/index.htm
  • kmn96

    54 Posts

    506

    0

    Posted May 26th, 2006 00:00

    There are two system boards for the E510. The older boards don't have sufficient VRM voltage to support the new procs. If you have the unsupported system board, the system will present you with a warning message that the processor is unsupported. I believe A01 and earlier motherboards don't have the VRM support. Easy way to check is to remove the heatsink and see if the component is there. Should be 4 round inductors instead of three on the new board.
  • audiomarkg

    13 Posts

    506

    0

    Posted May 26th, 2006 01:00

    Ok I will take a look. I am not really sure what I am looking for, (other than what you decribe in the note). If I get confused when looking at board, I will reply to your post again.. Sounds like you know what you are talking about.
  • audiomarkg

    13 Posts

    506

    0

    Posted May 26th, 2006 01:00

    Yes, I know the 945 chipset support the D, that is what is in now, D820. I am assuming with the new intel Core Duo 2's coming soon, the price the of the higher 900 D series will be dropping. Thanks for the info.
  • cmose

    7 Posts

    506

    0

    Posted May 27th, 2006 12:00

    is there any other way to determine this rather than removing the heatsink?
  • NemesisDB

    2 Intern

    •

    7944 Posts

    506

    0

    Posted May 28th, 2006 05:00

    the poster suggested looking at the revision of the board -- though he sounded less than confident about that part
  • 50pence

    166 Posts

    506

    0

    Posted May 28th, 2006 10:00

    I would like to know if there are different boards in the 5150 and how to tell however I am not sure if the VRM is relevant beacuse the 6XX and 9XX have the same voltage specs. 
  • cmose

    7 Posts

    506

    0

    Posted May 28th, 2006 21:00

    yeah if anyone has any more info on this I'd be most appreciative.
  • StrayTech

    20 Posts

    506

    0

    Posted May 30th, 2006 22:00

    I just tried to upgrade my e510/DM051 to a Pentium D 950.  (My current processor is a 3.2 HT...a 640 a believe.)  Absolutely no luck...and this is with the A05 BIOS.  Nothing but stuck POST and a solid amber light on the power switch.

    If Intel says the chipset supports the processor, Dell's freaking motherboard should support the processor.

    My system was purchased less than a month ago brand new from Dell.  The motherboard is stamped with an A00 revision.  (The preloaded BIOS was A05...and I reflashed it just to be sure.)

    It would be really freaking nice if there were a list of all the supported processors my system could use instead of this trial and error garbage.  Now, I have a brand new processor with nowhere to go.

    Thanks, Dell.

     

  • 50pence

    166 Posts

    294

    0

    Posted May 31st, 2006 10:00

    Hi
     
    What do Dell tech support say? Have you looked re the number of inductors under the heat sink as per the post above? Have you tried re setting the BIOS before starting the machine with the new processor installed? If not with the machine unplugged from the mains supply try taking out the CMOS back up battery and hitting the on switch a couple of times.
     
    I would also like to put a 940 or 950 in my machine and have been lead to beleive that both A04 and A05 BIOS should allow the 9XX processors to function (but for the 955 and I guess the new 965). My motherboard has "Rev" next to a white space on the bottom left hand corner, I guess this is where the revision would be stamped though there is nothing in there. Is this where you say yours is stamped?
     
     
    Regards.