UNSOLVED

froggy2

updated

23 years ago

F

froggy2

9 Posts

0

22584

November 6th, 2003 03:00

Software/Internet Explorer does not recognize a current internet connection

I have started having problems with some programs that require an internet connection. I have a cable modem which is always on and I may be on an connected web site and still some programs will say, "the computer currently has no connection to the internet and is unable to creat one". Or I will get the work offline box and if I click on retry it works. Or still another problem I have is with Windows Media player - when I click on a short video it says a connection is required, when I am on an active site.

Anyone have any ideas what is wrong here?

Thanks

  • DELL-Cody

    2 Intern

    •

    2166 Posts

    700

    0

    Posted November 6th, 2003 15:00

    Ensure your virus-scanning software is up-to-date, and then perform a full scan of your system and files.

    You may need to run a spyware removal tool on your system such as AdAware or SpyBot.

    If the above doesn't help, what is the status of the link lights on both the network interface on your computer and on the cable modem when this problem occurs? If you power off the cable modem and computer for about twenty minutes, then power the cable modem on, allow it to connect to the ISP, and then power on your system, do the problems persist?
  • froggy2

    9 Posts

    700

    0

    Posted November 6th, 2003 15:00

    Cody,

    Thanks for the response. I have done all three steps. Actually I shut the monitor, router, and my computer for about 2-3 hr. after running Spybot and updating Norton. Interestingly I have two computers, this one running XP and an older Dell Dimension XPS-233s and I don't have this problem with the latter.  My problem is on my Dimension 8200. Any other suggestions?

  • jmwills

    2 Intern

    •

    11984 Posts

    700

    0

    Posted November 7th, 2003 13:00

    What type of network setup do you have?  Are you assigning DHCP addressing from a router or running ICS?
  • froggy2

    9 Posts

    700

    0

    Posted November 7th, 2003 16:00

    J,

    Thanks for the question. I am assuming I am using DHCP addressing because when I look at the Support tab on my local area connection it says. "Address Type Assigned by DHCP", and this IP address is .3 and the Default is .1 When you ask "type" I am using a cable modem>router>2 computers.

  • 700

    0

    Posted November 9th, 2003 17:00

    Can you check in your Internet settings that its got LAN settings - Autodetect enable.

    Find this via - Start -> Control Panel ->Internet Options -> Connections -> LAN settings

  • froggy2

    9 Posts

    700

    0

    Posted November 10th, 2003 02:00

    Hi Sentinel-Master,

    Thanks for your suggestion, but I did verify that it is Autodetect enabled. This is really crazy. All my setting so far look correct. I think it there were some way to remove my network and re-install, that might help. Thanks again for your idea!

  • 700

    0

    Posted November 10th, 2003 20:00

    No your network settings and card are fine - by the mere fact you can browse the Internet and email etc etc.

    Try opening Windows Media Player on your PC - and select the Tools->Options->Network tab, and check that the various network ports are selected UDP, TCP, HTTP & Multicast

     

  • froggy2

    9 Posts

    700

    0

    Posted November 11th, 2003 02:00

    I checked Windows Media Player and they were all checked. This is really strange. I have the same problem with Quicken 2004. Every time it goes to check an account on the internet it says it cannot detect an internet connection. So it does not seem to be a software problem, I guess? But rather some setting in my computer?

     

    Thanks for your great persistence!

  • 700

    0

    Posted November 12th, 2003 15:00

    This is so weird - can you try disabling any Firewall s/w you have active on the PC and then re-try WMP or Quicken.

    Start -> Run -> cmd

    Also when you have these Applications open can you issue the command "nbtstat -s" and "netstat", and post the results here for perusal

  • froggy2

    9 Posts

    312

    0

    Posted November 13th, 2003 03:00

    When I run cmd I presume you want me to also run ipconfig /release? If so when I do I get the following: The operation failed as no adapter is in the state permissible for this operation.

    As for the second request, I am sorry but can you help me understand what you mean by "issue the command"?

     

    Thanks