UNSOLVED
P
PleaseUseEmailF
10 Posts
0
500471
December 6th, 2007 19:00
MD3000i and Modular Disk Storage Manager
Howdy Folks,
We have a brand new MD3000i iSCSI array. There are 4 servers connected to the array, via iSCSI, on a separate Cisco 3750 switch. The array management interfaces are on our production network. The configuration has been pretty simple, but I keep running into problems with the Modular Disk Storage Manager (MDSM).
After using the MDSM for a few days, it looses the connection to the storage modules on the MD3000i. I can still ping the management and iSCSI interfaces of the array and iSCSI still works flawlessly from the servers, but I can't manage the array at all.
The MDSM says the storage array is currently unresponsive. Removing the array and trying to add it back doesn't work. I have to physically power down the array to start managing it again.
I have checked all the ports for duplex/speed mis-matches on the network switches, but don't see any problems.
Any suggestions?
We have a brand new MD3000i iSCSI array. There are 4 servers connected to the array, via iSCSI, on a separate Cisco 3750 switch. The array management interfaces are on our production network. The configuration has been pretty simple, but I keep running into problems with the Modular Disk Storage Manager (MDSM).
After using the MDSM for a few days, it looses the connection to the storage modules on the MD3000i. I can still ping the management and iSCSI interfaces of the array and iSCSI still works flawlessly from the servers, but I can't manage the array at all.
The MDSM says the storage array is currently unresponsive. Removing the array and trying to add it back doesn't work. I have to physically power down the array to start managing it again.
I have checked all the ports for duplex/speed mis-matches on the network switches, but don't see any problems.
Any suggestions?
PleaseUseEmailF
10 Posts
2444
0
Posted December 7th, 2007 16:00
All iSCSI Network interfaces are on the 172.29.159.xxx/24 network. This network is not routed over our network at all and a dedicated switch is being used for these connections.
The production network is 10.96.159.xxx/24. The management interfaces live on this network.
I have a dedicated machine setup for iSCSI management using the out-of-band connections. I installed the management application on one of the iSCSI servers to test the in-band management, but was experience the same problems.
I have now found the problem gets worse when the MD3000i unit is under a heavy load. If I run the SQLIOSIM utility to test the unit, I am unable to access the management interfaces. If I kill the test and wait a few minutes, I can SOMETIMES get the unit back.
- Just to clarify, MDSM does not need to be installed on a iSCSI server that's connected to the array to utilize in-band. The management station with MDSM only needs to have UDP/TCP access to one (or more) iSCSI server and a proxy will manage communication to the array.Additionally only out-of-band management could be used with MDSM installed on a iSCSI server as long as the host has UDP/TCP access to the management ports on the array.Is Automatic or Manual discovery being used?Can you detail what the "Out-of-band management connection(s)" and the "In-band management connection(s)" on the Summary tab indicate?What OS's are running on the management station and host servers?Dave
PleaseUseEmailF
10 Posts
2443
0
Posted December 7th, 2007 21:00
I have tried both automatic and manual discovery modes. Both methods occasionally discover one of the controllers, but say the MD3000i can not be managed.
If I am able to make one of these “half” connections, the summary tab will show the IP address of one of the out-of-band management connections. But all of the tabs are blank and it says the array cannot be managed in this state. I don't have the specific error in front of me. (I rebooted the array earlier to regain access).
The management station and servers are all Windows 2003 R2 SP2.
Thanks for your help so far.PleaseUseEmailF
10 Posts
2443
0
Posted December 10th, 2007 12:00
I am using DHCP, but using reservations in DHCP so the array will always get the same IP Addresses.
When this problem occurs, I am still able to ping the controller IP addresses (management and iSCSI). I never lose that ability.During boot the controllers in the MD3000i will attempt to obtain management port IPs via DHCP, if a DHCP server is not available then the following default IP's will be used.
controller 0 - 192.168.128.101 Subnet Mask 255.255.255.0
controller 1 - 192.168.128.102 Subnet Mask 255.255.255.0
Can you perform the following steps and report the results?
1 - Configure a mini-network using the 192.168.128 subnet (e.g. assign 192.168.128.001 as the IP on a system)
1 - Unplug the network connections from each management port of the controllers
2 - Restart the array (the controllers will default to the static IPs)
3 - Once the status LED on the MD3000i is blue reconnect the management port connections
4 - From the system that is configured with the 192.168.128.001 IP ping the two controller IPs listed above
5 - Perform an Automatic discovery in MDSM (discovery should succeed and both controller IPs should be listed on the Summary tab)
Dave
PleaseUseEmailF
10 Posts
2443
0
Posted December 10th, 2007 13:00
I will have to get back to you on this test setup. I will do it, but it might take a few days.BTW, I lost management access to the array again over the weekend. This morning I am completely unable to access it. Automatic and Manual discovery do not find anything.My servers are still talking iSCSI to it, but I can't manage it in any way.PleaseUseEmailF
10 Posts
2443
0
Posted December 11th, 2007 14:00
It looks like Dell has released new firmware and drivers for the MD3000i yesterday. I am downloading them now and will try them out as well.- The latest release includes support for SATA physical disks in the MD3000 (and MD3000i) storage array.Even though you're using SAS physical disks if you have the opportunity to update the stack to the latest release please do and reply with your results.Dave
dzenz
175 Posts
2444
0
Posted December 7th, 2007 16:00